Recent content by Minkaxy

  1. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    I just clean it to take a pic. Maybe the blob drop from some of my brush.
  2. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks, I try to figure it out where is it too. This case have to reflow cpu and everything back to normal.
  3. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    This one come today, It cannot glitch when microsd is insert. Eveything look good, no blob at cpu.
  4. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    300 degrees and 3s to 5s same. I used to installed with sx, hwfly before and all of it work fine. but after the instinct-nx chip came out and I try it, this issued happen. and now I switch to use rp2040 the issued is still happen. so I doubt maybe myself did something wrong but I don't know...
  5. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Same, reflow the cpu and everything back to normal now. ok, let add the kapton tape then.
  6. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thank for reply. then I should switch to use the mosfet and see If it solve the problem. suspect the flex cable is a bad guy in my case.
  7. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    I will try the point on the back too. This switch v1 I installed rp2040 three days ago everything works fine after first try then sleep and today cannot turn it on. Led says bad cpu or poor wiring. I don’t know what went wrong now. Can you suggest anything on this motherboard.
  8. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    This is oled installed :) I think the solder point is correct. 3.3v is on the correct point. But the issued I mention before still occur on many device that I installed rp2040. Even instinct-nx I found the issued same. 1693799874 It happened to me many time I don’t know how maybe the switch...
  9. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    yep, I done the blue screen on lite model several day ago and don’t seem what cause it but I suggest that my hand shake when solder the 3.3 point and maybe the cap gone bad or something 1693762669 And do you think it can cause the heat to make cpu or emmc to be broken. Because most of the...
  10. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thank you. I will try that I found sometime after turn off the nintendo switch rp2040 try to glitch and after successful glitch then nothing happened. Maybe your fw can help. The emmc init failure that I found, I found shorted on the cap around emmc and I reball emmc and it fixed the issued...
  11. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Here is what i installed on v2.
  12. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thank for answer In oled i use this point same as the picture in attachment. V1,v2 too 1693761024 This is what i found on my phone but tomorrow I will take a new pic. And upload again.
  13. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello all, I’ve installed rp2040 to many nintendo. And I found many issued afrer 1 month. -switch restart itself after attach right joy-con -rp2040 cannot glitch if the micro sd is inserted. -found shorted at 3.3v -failed to init emmc(oled model) -rst is not connected but it worked before...
  14. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    I Have the same problem. I found shorted around Enxx Ic after I Installed picofly. Can you provide the picture of the resistor on pi zero? maybe the resistor was touch with the point on the board.
  15. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    I found shorted at MAX77620H I don’t know if firmware 2.67 did this or not. But before this I use 2.55 and no device give me any problem.
See more
General chit-chat
Help Users
    Jayro @ Jayro: Thanks for that bundle, I had the games already but got all the DLC for them for just $5. What a... +1