OLED HWFLY fail to reboot to CFW

[Melter]

Hoping someone can shed some light on a minor problem I'm facing with my HWFLY on my switch OLED - when rebooting within atmosphere around 90% of the time the HWFLY lights up Cyan on reboot and boots to OFW. I tried setting up reboot to payload in atmosphere config as well as explicitly disabling it with no difference.

When powering off and then powering on the switch form cold boot the chip boots hekate 100% perfectly each time, this issue only seems to occur on reboot.

I am also on the latest HWFLY version 0.6.2.

Has anyone faced a similar issue?

 

[Shrapn]

I am having the exact same issue! No resolution yet.

 

[Purple_Heart]

as far as i know Reboot to payload doesnt work on Lite and Mariko (OLED is Mariko)

 

[Hayato213]

as far as i know Reboot to payload doesnt work on Lite and Mariko (OLED is Mariko)

OLED is Aula, V2 is Mariko

 

[FR0ZN]

OLED is Aula, V2 is Mariko

Mariko is the name of the SoC, not the model.
Aula is also running on Mariko.

 

[Purple_Heart]

doesnt OLED (Aula) have simmilar internals (sry for bad english) like Mariko?

 

[Purple_Heart]

thats what i mean

 

[Hayato213]

Mariko is the name of the SoC, not the model.
Aula is also running on Mariko.

I think it is just easier to differentiate, if you says Aula people would know it is an OLED.

 

[Purple_Heart]

But not everyone knows what SoC Aula uses

 

[Draxzelex]

Hoping someone can shed some light on a minor problem I'm facing with my HWFLY on my switch OLED - when rebooting within atmosphere around 90% of the time the HWFLY lights up Cyan on reboot and boots to OFW. I tried setting up reboot to payload in atmosphere config as well as explicitly disabling it with no difference.

When powering off and then powering on the switch form cold boot the chip boots hekate 100% perfectly each time, this issue only seems to occur on reboot.

I am also on the latest HWFLY version 0.6.2.

Has anyone faced a similar issue?

Reboot to payload doesn't work on OLED units.

 

[estm13]

Hoping someone can shed some light on a minor problem I'm facing with my HWFLY on my switch OLED - when rebooting within atmosphere around 90% of the time the HWFLY lights up Cyan on reboot and boots to OFW. I tried setting up reboot to payload in atmosphere config as well as explicitly disabling it with no difference.

When powering off and then powering on the switch form cold boot the chip boots hekate 100% perfectly each time, this issue only seems to occur on reboot.

I am also on the latest HWFLY version 0.6.2.

Has anyone faced a similar issue?

same as mine, after resolder sp1 and sp2 everything run perfectly

 

[CompSciOrBust]

as far as i know Reboot to payload doesnt work on Lite and Mariko (OLED is Mariko)

Reboot to payload doesn't work on OLED units.

Even without reboot to payload Mariko / Lite / Oled models will reboot to the payload on the SD Card as if it is doing a cold boot. There's probably something wrong with the firmware on OP's chip because my Oled and Mariko can reboot in to Hekate automatically on fatal.

Edit: Or an issue with the soldering, as estm13 pointed out.

 

[Thorhax]

I am having the exact same issue! No resolution yet.

me as well

 

[Bubbles21]

does your mod chips for oled have LED lights? mine has and its stuch on slow blink purple then fast blink orange/green

 

[Thorhax]

does your mod chips for oled have LED lights? mine has and its stuch on slow blink purple then fast blink orange/green

yup

 

[burhansalih]

 

[Bubbles21]

Is there a way or technic so I can boot normally again? any software i could use just like injecting payload in v1?

 

[burhansalih]

Is there a way or technic so I can boot normally again? any software i could use just like injecting payload in v1?

For OLED?

 

[Melter]

I’ve seen this chart. When the reboot fails I get the solid cyan color (FPGA error) so I’m not sure what it means. I have also updated to the latest version of the firmware and still getting the same issue.

I don’t think it’s a problem with the soldering since the chip works 100% of the time on cold boot, and fails (almost) 100% of the time on reboot.

it’s not really a big deal since I can just power off and back on easily enough if I need to reboot but would be nice if there was a way to get it to work in all cases.

 

[estm13]

I’ve seen this chart. When the reboot fails I get the solid cyan color (FPGA error) so I’m not sure what it means. I have also updated to the latest version of the firmware and still getting the same issue.

I don’t think it’s a problem with the soldering since the chip works 100% of the time on cold boot, and fails (almost) 100% of the time on reboot.

it’s not really a big deal since I can just power off and back on easily enough if I need to reboot but would be nice if there was a way to get it to work in all cases.

hi, let give a try to update your hekate and nyx to latest version maybe will solve your problem