Search results

  1. Lazr1026

    Wii U Stuck on Logo

    ah yeah, thats RESET. pulling it low will absolutely make it not boot
  2. Lazr1026

    de_Fuse, a Wii U modchip in development by ShinyQuagsire

    if you ripped the pad, there is absolutely no way you will be able to use the alternative vias.
  3. Lazr1026

    Wii U Stuck on Logo

    I just saw this, and yeah, i stripped a large section at the end of the wire (super easy to do with magwire!) and then to wherever it needed to go.
  4. Lazr1026

    Wii U Stuck on Logo

    yeah its shown in the picture (wire to TP122). its the pin right below VBUS (in the top right corner by the USB port)
  5. Lazr1026

    Wii U Stuck on Logo

    the vias have a bit of soldermask yeah. you should scratch them before tinning them, if you go that route. I don't actually remember what i did about power in the first pic. The pico was being powered by the PC. but maybe I hooked up 3v3 after..? 1729199151 ohhh wait. 3v3 is going to the VSYS pin
  6. Lazr1026

    Wii U Stuck on Logo

    yeah that was mine. I've put together systems with de_Fuse still installed, and they closed fine. tbh anywhere that isnt too close to the mounting holes is fine, i've even put the pico next to the wifi module once: Or you could secure it on the topside and use the debug vias next to the 1v...
  7. Lazr1026

    Wii U Stuck on Logo

    heh, i didn't even realize how close the pico was to that screw hole! I didn't plan to close that system at all, but i would move it away as the bottom shield will come in contact with the pico. Nothing uses those pins but will be a pita to secure the bottom shield.
  8. Lazr1026

    Hacking Hardware Homebrew Nandaid help!

    honestly at this point I think you should just use redNAND. save yourself the hassle of this.
  9. Lazr1026

    Tutorial Region Changing the Wii U

    Did you erase both the eMMC and scfm.img?
  10. Lazr1026

    Hacking Hardware Homebrew Nandaid help!

    set your meter to continuity mode (like shown) and put the probes on each pad. test each of them against each other.
  11. Lazr1026

    Hacking Hardware Homebrew Nandaid help!

    Please send a picture of your solder work
  12. Lazr1026

    Tutorial Region Changing the Wii U

    you can, but it was not exactly safe to begin with
  13. Lazr1026

    Wii U Brick????

    its my post yes. you say you can still access EnvironmentLoader, which is perfect, since you can load minute still and install isfshax.
  14. Lazr1026

    Wii U Brick????

    he could do an actual region change. you can find the guide for that here on gbatemp
  15. Lazr1026

    Hacking Can’t use GC controller in wii games on usb loader gx

    Theres no need for a patch when the Wii U has a native SI data line, which you can use to play Wii games/homebrew that support the GCN Controller without any patches, just a few wires. I wrote a small guide on BitBuilt on how to do it...
  16. Lazr1026

    Tutorial Region Changing the Wii U

    The WiFi connections are stored on the SLC, so the Wii U should still use them before even setting up the network configuration.
  17. Lazr1026

    Wii U Internal Storage Upgrades are possible

    the usata is open source and you can order the PCBs from jlcpcb/pcbway and the parts in the BOM can be gotten from digikey/mouser.
  18. Lazr1026

    Unable to dump OTP.bin

    mcp_recovery!
  19. Lazr1026

    Unable to dump OTP.bin

    later on i can send you some ddi images, but it will be a few hours
  20. Lazr1026

    Unable to dump OTP.bin

    no, but its better to still have it now just in case you need it later
General chit-chat
Help Users
    Xdqwerty @ Xdqwerty: @Psionic Roshambo, I don't care for Trump, i didnt even know who he was before he became...