Recent content by TheBorg

  1. T

    Hacking 3DS unbricking progress

    Thanks all... i'm going for the model B..
  2. T

    Hacking 3DS unbricking progress

    Is there a different in using the Raspberry Pi model B 512 MB or Raspberry Pi model A 256 MB?
  3. T

    Hacking 3DS unbricking progress

    mmmm Woon je toevallig ergens in de buurt van haarlem? Dan buurt ik ff langs... ;) Gaat denk ik niet lukken met mijn boardje.
  4. T

    Hacking 3DS unbricking progress

    Want to try it. But i must know for sure where i can connect the 3.3V. i have a 3ds xl.
  5. T

    Hacking 3DS unbricking progress

    I tried to turn on 3ds without any connection, direct blue screen, CLK = 0V and no CLK pulsing. I tried to turn on 3ds connected to my Board and tried on PC, it's for 3 seconds black and then blue screen, CLK = 0V and no CLK pulsing. Then in both states i make output CLK to high on my board and...
  6. T

    Hacking 3DS unbricking progress

    I tried it with 100K, 47K 20K and 150ohm resistor with no luck.. (2.5V) I think i need a TTL instead of open collector?
  7. T

    Hacking 3DS unbricking progress

    With 3ds off or on CLK = 2.3V. i do not understand: measure the voltage of CLK in your fake SD with 3ds on? i think i know what you mean, with 3ds on i measure on the 3ds sd card cable: DAT3 = 3,3V CMD = 3,3V CLK = 0V DAT0 = 3,3V With 3ds sdcard connected to my board en put CLK, CMD and DAT3...
  8. T

    Hacking 3DS unbricking progress

    This board works on 3.3V. On all outputs i use pullup resistors 47Kohm With SD card connected, all outputs are 3.3V on the sd card. With 3ds connected, CS and DO are 3.3V, but CLK is dropping down to 2.3 V. i tried it with a pullup of 150ohm. With a sd card all is working, with 3ds not. Only...
  9. T

    Hacking 3DS unbricking progress

    Hello, I have a RCM6700 proc board from rabbit. I change all code i found and made it work for this board. Now i can lock/unlock a sd card with a password and can erase a locked sd card. All working on differents sd cards. I'm try the same on a bricked 3ds XL and it's not working. I...
  10. T

    Hardware nand flash dump (3ds xl)

    https://github.com/Nephiel/sdlocker-tiny Maybe change the program inside and add the reset/clear commando. Only don't know where connect the *CS signal.
  11. T

    Hardware nand flash dump (3ds xl)

    - Someone with a brick should take the backup of their 4.x bios and raw write it to an SD with winimage, insert, cold boot and just see what happens. Test it, same result... no boot and read/write error.
  12. T

    Hardware nand flash dump (3ds xl)

    Program sees the 1GB disc but give read and write errors.
  13. T

    Hardware nand flash dump (3ds xl)

    Hello, i tried USB Image Tool on a normal SDCard 1GB and restore the 3DS NAND to it. I restart the USB Image tool and look at Device Mode: Reading and writing the NAND again and all went OK on the 1GB SDCard. Now i connect the GW bricked 3DS and open the USB IMAGE Tool: Look like...
  14. T

    Hardware nand flash dump (3ds xl)

    I have the same problem, with selecting a drive letter. This trick doesn't work on a GW Brick. The SD trick NAND backup/restore only work on a working 3DS and not on a GW brick 3DS. We must wait for an another solution.
  15. T

    Hardware nand flash dump (3ds xl)

    Hi, Excactly the same happend to me. I tried 6 different laptop's and 4 card readers withoud any results. I also tried the All in 1 Mini Card Reader they said on this forum it's working, this is not working by my to and doesn't sees the flash. Only 1 laptop is seeing the 3DS in correct size...
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    Psionic Roshambo @ Psionic Roshambo: https://www.youtube.com/watch?v=iIpfWORQWhU