Recent content by giovany86

  1. giovany86

    Picofly work with only SP1

    haven't done an install for over three weeks so couldn't try, but i'll try on the next lite i'll do
  2. giovany86

    Picofly work with only SP1

    Guess i've stumbled on 2 Lite units that weren't in the mood for one sole mosfet then x)
  3. giovany86

    Picofly work with only SP1

    If i remember correctly, Erista unit (V1 & Patched V1) only require one mosfet and therefore, should work even with only one cap soldered. I tried it two times and worked well, the only potential issue i could see is in case you did a cold joint and it stop making contact but you should be fine...
  4. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Please, put the iron away and post all of your soldering
  5. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Please, stay away from that board and send it to someone with enough skill and tools to fix it before it's dead
  6. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Assuming you have the tools to do so, you'll need to remove the emmc chip and run a jumper wire from emmc pad to the still standing point next to the one you damaged. And by looking at the board scan, you clearly don't want to expose more copper as it's a ground plane and you'll most likely...
  7. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello there. I've installed one RP2040-Zero on a Lite and it have a weird glitching time. If i let it off for a few hours, the next glitch will take up to 10 seconds, whereas if i turn it on after a few minutes, it will glitch in under 5 seconds. Is this a normal behavior ?
  8. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello there, after reading a bit, is the pull-down resistor mandatory on the mosfet and what are the risk of not doing it ? I've done 2 dual-mosfet install without issue but i'm worried after reading these posts x)
  9. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    I have a small doubt about my RP2040-Zero, after flashing i have a yellow light. If i plug it to my computer, i have a blue light. So i don't need to bridge the RGB Mode Jumper, right ?
  10. giovany86

    Hacking RELEASE Lockpick_RCM payload - Official Thread

    Instantly re-upped it to Archive.org under a temp account. Guess we're up for a mouse & cat game again.
  11. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello there, with the last UF2 version, do we still have to do the unlock thing with Hekate ?
  12. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Talking about your switch ? x)
  13. giovany86

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello there, As lots of people already said before, it might be today or in a year, we don't know when it will be working as it needs to be reverse-engineered (as i understand) and not only patched. If you want something to mod your switch "fast", you better buy a HWFly but if you like to...
  14. giovany86

    RGH3 Chipless Glitching!!

    Mine did the same thing after flashing the file with the wrong mode selected. Might be a short-circuit / false-contact on your board, did you checked for any thing that could prevent it from booting ?
  15. giovany86

    RGH3 Chipless Glitching!!

    I'm currently trying it on one of my original Falcon, i'l stuck at the ecc step, how do i boot XELL Reloaded without a modchip ? UPDATE : One of my solder was bad, and i was writing the ecc as "Retail" and not as" Glitch2". Now everything boot just fine ! UPDATE 2 : Compared it with my first...
See more
General chit-chat
Help Users
    Purple_Heart @ Purple_Heart: ye