Recent content by Browbon

  1. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    It happens on my V2 one time, show slow emmc mode but after i restart, it become normal without issue. Do i need to put more resistor too?
  2. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanh for suggesting. Im not familiar with reddit. I tried to find schema for hours and most of subreddit regarding to my keyboard is on “protest” mode to fight against reddit. Shall you suggest where or what site i can ask for infomation? Thanks
  3. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    CLear
  4. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    As debug list in V6 guide, I can say there is something wrong with your mosfet or you mosfet installation.
  5. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    can you show us the error video? For better debug
  6. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    @deeps @QuiTim Are there any other alternative point for gnd and 3.3v point on Lite? 2 point on V6 guide is a little bit far for me, Thank you.
  7. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    the C1 tip makes sense such as solder between 2 components, thats also why i want some smaller tip
  8. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi everyone, I would like to buy a new tip for modding in future. After struggling with my too big solder tip, I found this one Is it suitable for this kind of modding? Or have any better replacement? Im in Asia so shopee or aliexpress is a prefer. Thank you.
  9. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    can you show me some alternative gnd point? my knowledge of electronics is humble (above zero a little bit). thanks! 1686649486 Im learning too. For unstick pad, i think you can add some flux on it and try to tin it gently. It will hard at begin but after 4-5 time trying to tin the pad, the...
  10. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    this's not my installation, its someone else. I have seen this installation use alternative 3.3v point and gnd point different from the picture on V6 guide. It avoid using the point near M92T36 IC that reduce the failure chance. It will help me improve the next installation and avoid my mistake...
  11. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    I did the research and found on old topic that have this ground point. It look safer and easier than the point on V6.2 guide
  12. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    What is the alternative GND point on V2 instead of the point at capacitor near M92T36 IC? I have seen that there are many gnd point on mobo in v6.2 guide
  13. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    I agree with it but in some case i need the smaller one to tin the point, like this RST point on my V2 as you can see, i only tin one point and can not reach to the other. It made me struggle because it detach many time. Mostly I use the regular tip for bigger pad
  14. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi everyone, after almost breaking the capacitors near M92T36 IC, I realized some problem. My solder tip is too big for modding. Then I found some smaller tip. How do you think about it? Shall it good enough for modding in future
  15. Browbon

    Hacking Hardware Picofly - a HWFLY switch modchip

    it's really the hardest point i ever solder
See more
General chit-chat
Help Users
    SylverReZ @ SylverReZ: https://www.youtube.com/watch?v=dbSORc_3_Yw