Recent content by blackheartme

  1. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    i suppose its a wrong thread to ask, but to answer your question 42C is within normal temperature, as tegra x1 SOC working temp -40C to 80C, as for switch i consider 60C the max threshold that i would consider the device needs repaste or change fan as ninjas underclock their device lower than...
  2. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    i see, id better use a new adapter then to make sure, the slow emunand problem keep confusing me lol thanks for your input
  3. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    already use dual resistor, on this particullar OLED booting to ofw black screen, no sd card screen apear just fine , booting to hekate normal but slow emmc mode, can dump keys and can make emunand but havent tried launch it yet as i believe its gonna blackscreen also like ofw. i want to ask...
  4. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    does bad dat0 connection on OLED (too long wires/uncleaned flux/short because of bad Dat0 adapter) can cause EMMC SLOW MODE? note: already using extra 47R on dat0 and CMD
  5. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    thats a good information to know :teach::teach:
  6. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    the trick is to avoid it at all cost and find easier spot like the chasis, less hasle and low risk of damaging the soc from high temp
  7. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    im a bit curious can you corrupt nand from shorting the emmc dat0 or other cause? i have one OLED that seems have that case, after instal pico cannot boot OFW, can enter hekate with no sd screen etc but when you try make emunand emmc cannot read, sysnand cfw also wont launch
  8. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    just curious anyone have any issue of slightly warm switch after picofly instal ? 41-44 Celcius idle and about 47-50 while playing example zelda (FYI this is one of the first v1 i modded, and i did cut the shield abit to fit pico firstime ), also this unit have battery drain problem i just...
  9. B

    Picofly AIO Thread

    search bar? or google ? anyways ive used few of those, regarding quality VS standard Rp2040 its the same, the slightly better thing about it is easier and cleaner installation, although that depends mostly on the installer. if you want less hassle with extra price just go for it, if you want...
  10. B

    Picofly AIO Thread

    why dont use the pico zero instead or tiny less hassle
  11. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    try docking it while you think its on, sometimes it happened like mine broke stupid connector black screen but on
  12. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    yeah found out my oled problem the Display connector pin are bent, damn those connector, had to pay $15 to replace those connector
  13. B

    Picofly AIO Thread

    its on while docking
  14. B

    Picofly AIO Thread

    another attempt on 2nd OLED, damn my screen wont turn on but it got sounds:cry::cry: (this before instaling rp2040, one final test to OFW ), does anyone have any idea what to check ? :unsure: :unsure: , all connector seems fine already triple checked
  15. B

    Hacking Hardware Picofly - a HWFLY switch modchip

    another attempt on 2nd OLED, damn my screen wont turn on but it got sounds:cry::cry: (this before instaling rp2040, one final test to OFW ), does anyone have any idea what to check ? :unsure: :unsure: , all connector seems fine
See more
General chit-chat
Help Users
    AncientBoi @ AncientBoi: done