Trinket M0 won’t let me transfer files to it again

[kylum]

Ordered a new trinket, honestly had enough of this one. Any tips for the new one?

Nothing other than reading OG Trinket threads by @mattytrog posted to get an understanding.

Thank you for sharing how to solve this problem?

Did something help you?

 

[Swarmx]

Nothing other than reading OG Trinket threads by @mattytrog posted to get an understanding.

Did something help you?

hey so i got the vol up working and power etc now just the vol down doesnt wanna work do you know what controls this? or what i can do to fix this



update: switch boots both ofw and cfw although cannot seem to located payload.bin on root of sd card so i have to manually inject with pc

 

[kylum]

What’s up with the volume -/+ issues you keep dealing with, thought it was only + button? What did you do to get + going?
This with the old/new trinket installed?
What guide are you following?
Which uf2 files have you used for flashing?
Have you tried to enable autoRCM in hekate to see if payload pushes then?
Have you tried holding vol+ while powering on or holding both power and vol+ while powering on? If installed and flashed properly you will see a slider!

 

[Swarmx]

What’s up with the volume -/+ issues you keep dealing with, thought it was only + button? What did you do to get + going?
This with the old/new trinket installed?
What guide are you following?
Which uf2 files have you used for flashing?
Have you tried to enable autoRCM in hekate to see if payload pushes then?
Have you tried holding vol+ while powering on or holding both power and vol+ while powering on? If installed and flashed properly you will see a slider!

OK sorry for the late reply i had been working on it all day so what happened got everything working, just volume down is fixed, the vol plus issue happened with the resistor and the clip was also faulty for the ribbon so both were replaced and worked perfectly just the volume down needs to be fixed then ill have a fully working console

 

[kylum]

So trinket is working as expected?

 

[Swarmx]

So trinket is working as expected?

Yes, now it’s just the volume down and battery drain xD, this isn’t going well haha

 

[kylum]

At least you got it working. So that’s great news. Not to sure about the battery drain. The trinket barley uses anything at all. The only time I personally had a battery drain was because of autoRCM and the switch not actually powering completely off. I’m not sure but Atmosphere fixed that issue a long time ago if your using AutoRCM but the trinket could interfere with that maybe.

Did you have battery issue prior?

 

[Swarmx]

At least you got it working. So that’s great news. Not to sure about the battery drain. The trinket barley uses anything at all. The only time I personally had a battery drain was because of autoRCM and the switch not actually powering completely off. I’m not sure but Atmosphere fixed that issue a long time ago if your using AutoRCM but the trinket could interfere with that maybe.

Did you have battery issue prior?

to be honest i probably did but i noticed it now i guess but i think its fine im just being a bit paranoid i assume because ive seen some forums for battery life on trinket switch haha. Do you know where i can get the schematics for the nintendo switch power button/ vol down button so i can see where it is not working.

 

[kylum]

Actual schematics don’t exist but someone might have had the same issue if you look around. I will also look but please don’t wait on me!!!

 

[Swarmx]

Actual schematics don’t exist but someone might have had the same issue if you look around. I will also look but please don’t wait on me!!!

have had a try to look around and havent managed to find anything at all is a pain when all i need a working vol down and its perfect

 

[kylum]

No luck either. I would test functionality at the ribbon cable and work back from there checking for continuity and shorts. Make sure there isn’t a bridge or solder ball floating around you didn’t notice before

 

[Swarmx]

No luck either. I would test functionality at the ribbon cable and work back from there checking for continuity and shorts. Make sure there isn’t a bridge or solder ball floating around you didn’t notice before

ribbon cables work fine, just dont know which pin is used from the vol down so it becomes hard to track down

 

[kylum]

Use a multimeter to test for continuity from the button to the pins. Unplug the battery unless your looking for voltage. Don’t bridge pins with the prob if your testing with the battery connected.