Hacking [Tool] Joy-Con Toolkit

[binkinator]

Hi, tobygg! Can you give some instructions how you actually wrote your user values as factory values?
I have installed new anbernic's hall sensor joystics (they are drop replacement joystics btw), but they need to be calibrated. My user calibration seems to do no difference and has no effect.

He’s not been on the site in almost 2 years, mate. Slim chance of a response.

 

[impeeza]

you alway can fork and make the needed changes, the original repo has been changed on so long:

everyone have right to be busy. the guy has been make lots and lots for the scene.

 

[Xyphoseos]

is there a way to change button color individualy? My SL SR and ABXY are different

 

[impeeza]

is there a way to change button color individualy? My SL SR and ABXY are different

No with this tool and seems the console do not allows that

 

[EpochWon]

I replaced the right stick in my pro controller, but the min/max is different from what the switch expects. I recalibrated it with the tool and it works perfectly when using the playground, but when I connect it to my switch it doesn't use the calibration at all. I can't recalibrate in the switch because the stick isnt reaching all the way to the right.

 

[NeoHoth]

I replaced the right stick in my pro controller, but the min/max is different from what the switch expects. I recalibrated it with the tool and it works perfectly when using the playground, but when I connect it to my switch it doesn't use the calibration at all. I can't recalibrate in the switch because the stick isnt reaching all the way to the right.

That is exactly what I faced when I was playing with raw data and successfully calibrated my K-Silver hall effect joysticks to a center position.

Writing these new values to SPI of a joycon does nothing in regards to user calibration.

Upon reconnecting to the tool the recalibrated data seems to be intact, but once it is connected to Swich, all of this is disregarded.

I wonder whether the recalibrated values are just memorized by the tool itself rather then by a joycon. Or it is more likely that the Joy-Con Toolkit is not writing user calibrated values to the right binary slot of an SPI🤔

 

[Justsomecat]

Does this program still work?
And does it still receive updates?
I'm new and am just looking for knowledge.

 

[impeeza]

Does this program still work?
And does it still receive updates?
I'm new and am just looking for knowledge.

the program has been worked always, no updates recently because there is no need of them, go to github and look the readme.

 

[STUNT1990]

I'm trying the 5.2 version of joycon toolkit and I was able to dump the SPI (slowly but it did) however when I try to change the joycon color I don't even get to the color selection screen and I get the following error:

Edit: nvm, I didn't manage to figure it out on time but my switch's buyer didn't mind the original joycon colors showing up while conected to the system

 

[pepparkakahus]

Hi! Can't change color of Iine Neptune.. Go to Body & Button Color, choose colors, press ok, press Write Color, confirm the choise and then its grey again(( What am I doing wrong?

 

[AMOI]

Do you have the .net framework it needs installed?

IT DOES NOT WORK ANYMORE

 

[Hayato213]

IT DOES NOT WORK ANYMORE

Make sure you fulfill the prerequisite requirement.

 

[impeeza]

IT DOES NOT WORK ANYMORE

for me works fine!

 

[josete2k]

Yeah, I still use this program to get my unused joycons to factory mode.

 

[Guidion]

Before it gets asked... Here are the colors for the Zelda: Tears of the Kingdom Joy-Con

Body: #D2BE69 (210 190 105)
Buttons: #32322D (50 50 45)

Post automatically merged: May 5, 2023

is there a way to change button color individualy? My SL SR and ABXY are different

No there is not. This is a fault of the way the switch reads them. The Joy-Con themselves only have two colors that are stored, the body, and the buttons. The Pro Controller only has 4 colors that it stores, The Body, the Left handle, the Right handle, and the Buttons. There is no way to import any more as the switch itself only looks for two colors on Joy-Con and 4 on the Pro Controller.