Homebrew Update: 10.6.0-31 Homebrew Status

[Pikm]

where do i get ntr 3.3? :\

I dunno. I'm just going by what other people say.

 

[Commandertemp]

I dunno. I'm just going by what other people say.

link to 3.3 needed

 

[Pikm]

link to 3.3 needed

I don't know.

 

[thatbooisaspy]

.

 

[Commandertemp]

NTR 3.3 doesn't even exist.

topkek
ntr doesnt work on the latest fw, gateway emunand

 

[Pikm]

.

 

[Toni456]

topkek
ntr doesnt work on the latest fw, gateway emunand

Doesn't work for me either, but it could be because im running AuReiNand on sysnand through arm9loaderhax.

 

[DeathChaos]

NTR 3.3 doesn't even exist.

Instead of just looking at the very first post and leaving, you should've delved a bit deeper.

https://github.com/Shadowtrance/BootNTR/releases

 

[thatbooisaspy]

.

 

[DeathChaos]

Sorry for not looking at a fork, but what changed in NTR CFW 3.3?

Not that much actually changed, just support for latest emuNAND FW, although it still only supports up to 10.2 NATIVE_FIRM

 

[vialite]

It's not permanent thought right? browser/ menuhax will be brought up to date eventually right?

 

[thatbooisaspy]

.

 

[Pikm]

It's not permanent thought right? browser/ menuhax will be brought up to date eventually right?

Both probably, but Browserhax is more likely.

 

[ChicagoMel]

How do I use Save Manager with OOTHax if OOTHax requires the cartridge? (I'm going to get a copy and install OOTHax since Menuhax died and I can't afford Ninja)

 

[Pikm]

How do I use Save Manager with OOTHax if OOTHax requires the cartridge? (I'm going to get a copy and install OOTHax since Menuhax died and I can't afford Ninja)

You only need the Oot card to boot the hbl. After you're in, homebrew runs independently.

 

[Pikm]

How do I use Save Manager with OOTHax if OOTHax requires the cartridge? (I'm going to get a copy and install OOTHax since Menuhax died and I can't afford Ninja)

Also, if you're planning to install oothax on 10.6, you're out of luck. You need to find a friend on older firmware to install the hacked save on to the card.

 

[grubgrub]

Not that much actually changed, just support for latest emuNAND FW, although it still only supports up to 10.2 NATIVE_FIRM

Hey, sorry for the nub question, Ive been on 9.0 emunand for a long time and decided to update to the latest. I updated my 9.0.28 emunand to 10.6 emunand. I tried to run NTR but it gives the firmware not supported error.
You mentioned NATIVE_FIRM 10.2. Does that mean I will have to downgrade my native firm? How would I go about doing that.

Thanks again

 

[DeathChaos]

Hey, sorry for the nub question, Ive been on 9.0 emunand for a long time and decided to update to the latest. I updated my 9.0.28 emunand to 10.6 emunand. I tried to run NTR but it gives the firmware not supported error.
You mentioned NATIVE_FIRM 10.2. Does that mean I will have to downgrade my native firm? How would I go about doing that.

Thanks again

What CFW are you running?

I know that Cakes and RxTools use 10.2 NATIVE_FIRM, don't know about ReiNAND.

 

[ChicagoMel]

Also, if you're planning to install oothax on 10.6, you're out of luck. You need to find a friend on older firmware to install the hacked save on to the card.

Even with powersaves? I read that method still worked on 10.6

http://imgh.us/haxes.svg

 

[grubgrub]

What CFW are you running?

I know that Cakes and RxTools use 10.2 NATIVE_FIRM, don't know about ReiNAND.

I'm using Reinand V3.2. (https://github.com/Reisyukaku/ReiNand/releases)
I saw the there is a v3.2b but not too sure how to install that.