There's a Trinket m0 in my switch?! How do I make it work?

Discussion in 'Switch - Backup Loaders & Modchips' started by alexforreality, Feb 10, 2019 at 9:47 PM.

  1. linuxares

    linuxares I'm not a generous god!

    Moderator
    14
    Aug 5, 2007
    Sweden
  2. 210modz

    210modz GBAtemp Regular

    Member
    4
    Aug 11, 2017
    United States
    Damn that's one ugly install. I hate people that hot glue wires.
     
  3. alexforreality
    OP

    alexforreality Member

    Newcomer
    1
    Sunday
    United States

    can you point me to the argon uf2 files? i've been searching for hours.
     
  4. 210modz

    210modz GBAtemp Regular

    Member
    4
    Aug 11, 2017
    United States
    Why not just use hekate?
     
  5. Kubas_inko

    Kubas_inko "Something funny goes here."

    Member
    12
    Feb 3, 2017
    Czech Republic
    I gues on earth.
    You don't need config for argon. And looks nice (it is supposed to be burg like bootloader). Also, it will get (already has?) touch support.

    — Posts automatically merged - Please don't double post! —

    I see. So, his uf2 files has multiple payloads. Never used his uf2 files. You can probably choose which payload you want to load.
    If you want, I can guide you through arduino setup.
     
  6. Kafluke

    Kafluke GBAtemp Psycho!

    Member
    12
    May 6, 2006
    United States
    I have a trinket and I just use the universal file on it. Then I can switch payloads by putting the payload on the SD and renaming it to payload.bin. argon is good too
     
  7. alexforreality
    OP

    alexforreality Member

    Newcomer
    1
    Sunday
    United States
    That would be fantastic! Yeah I went through all of the pages of that thread and couldn't pinpoint what files I should be using where and which ones I needed. I had copied the "3 files" over to boottrinket several times but couldn't get the switch to boot anything unless I injected from my dongle or desktop. Renamed Target payload to payload.bin but I'm sure I was doing it wrong. Sometimes it would boot a payload if I pressed the reset on the chip but would freeze at the splash screen.
     
  8. Kubas_inko

    Kubas_inko "Something funny goes here."

    Member
    12
    Feb 3, 2017
    Czech Republic
    I gues on earth.
    you can always use Arduino ide and install 1 specific payload on the trinket.
     
  9. alexforreality
    OP

    alexforreality Member

    Newcomer
    1
    Sunday
    United States
    Explain it to me like I'm 5
     
  10. Kubas_inko

    Kubas_inko "Something funny goes here."

    Member
    12
    Feb 3, 2017
    Czech Republic
    I gues on earth.
    You download arduino ide, install it, install correct boards, put trinket into flash mode, get the correct payload, flash, profit.
     
    MorningBlunt likes this.
  11. mattytrog

    mattytrog Not on my watch.

    Member
    10
    Apr 27, 2018
    United Kingdom
    To OP... You are using obsoleted files.

    That was my old approach. If you still want S2 files, I think they are still on my git somewhere.

    Better off using Simple-UF2 though

    :)
     
  12. alexforreality
    OP

    alexforreality Member

    Newcomer
    1
    Sunday
    United States
    I emailed xboxexpert actually, because I'd seen his youtube video of him loading from a trinket and he provided me with a UF2 file that straight up loads ArgonNX pressing Vol+ and Power. oddly enough it also worked when I ONLY pressed the power button as well. I'm all set, guys, thank you for your time!
     
Loading...