1. Modificatorul

    Modificatorul GBAtemp Regular
    Member

    Joined:
    Oct 28, 2009
    Messages:
    179
    Country:
    Romania
    Last edited by Modificatorul, Jul 15, 2020
  2. squee666

    squee666 Trusted SX Core/Lite Installer
    Member

    Joined:
    Sep 17, 2010
    Messages:
    2,051
    Country:
    United Kingdom
  3. Astur_torque

    Astur_torque GBAtemp Regular
    Member

    Joined:
    May 19, 2020
    Messages:
    191
    Country:
    Spain
    Installed! iwthout microscope
     
  4. Alramir

    Alramir Mainline Injector
    Member

    Joined:
    Jul 6, 2020
    Messages:
    222
    Country:
    United Kingdom
    Brave, I know my hands are nowhere near steady enough :ha:
     
  5. Modificatorul

    Modificatorul GBAtemp Regular
    Member

    Joined:
    Oct 28, 2009
    Messages:
    179
    Country:
    Romania
    So tx confirmation was refering(@AshC95) just to the left side not on tegra, not good, now i have to fiind and edit my sugestions, when i have time will remove one and test.

    Did you removed and mesured ?
     
  6. squee666

    squee666 Trusted SX Core/Lite Installer
    Member

    Joined:
    Sep 17, 2010
    Messages:
    2,051
    Country:
    United Kingdom
    We had someone remove and measure and it came up 800nf.
    The thing is that cap doesnt exist. The best solution is that its 1000nf with resistance
     
    Modificatorul likes this.
  7. Tinkerbell

    Tinkerbell Member
    Newcomer

    Joined:
    Jun 29, 2020
    Messages:
    32
    Country:
    United Kingdom
    Any news on firmware 10.1 compatability and the SX-Lite? Also, how would I install it on emunand? Without Choidujour and access to Ninty servers I don't know how to do it.
     
    Last edited by Tinkerbell, Jul 15, 2020
    S_Sustain likes this.
  8. S_Sustain

    S_Sustain Member
    Newcomer

    Joined:
    May 19, 2020
    Messages:
    35
    Country:
    United Kingdom
    It works really well doesn't it. . It opens up a load of options. Kodi etc. Pretty much anything that will run on a pc. I might even get to play some of the Steam games that I've been hoarding :D
     
    caldeio likes this.
  9. squee666

    squee666 Trusted SX Core/Lite Installer
    Member

    Joined:
    Sep 17, 2010
    Messages:
    2,051
    Country:
    United Kingdom
    Curious what tiontemperature you used
     
  10. vvaitforme

    vvaitforme Member
    Newcomer

    Joined:
    May 25, 2020
    Messages:
    19
    Country:
    Turkey
    .
     
    Last edited by vvaitforme, Jul 15, 2020
    ModderFokker619 likes this.
  11. ModderFokker619

    ModderFokker619 GBAtemp Maniac
    Member

    Joined:
    Oct 2, 2015
    Messages:
    1,408
    Country:
    United States
    Same Same

    Emunand Working
     
  12. snk2

    snk2 Advanced Member
    Newcomer

    Joined:
    Nov 27, 2005
    Messages:
    78
    Country:
    Romania
    he is asking about 10.1.0, not 10.0.1
     
    Tinkerbell likes this.
  13. spoggi

    spoggi Member
    Newcomer

    Joined:
    Jun 5, 2020
    Messages:
    44
    Country:
    Denmark
    thought it was safe to update.
    I just removed my Core and plugged back nand in motherboard because i would like to update from 7.1 to 10.1
    but now all i got is blue light.
    Am i screwed or is there something i can do to get it to work again.Now im on 10.1
    can you please help me Thanks.

    FUCK i read wrong it was 10.0.1.4 and not 10.1 that was safe
    Sorry looks like it still works just took a minute to go green
    now it turns green right away
     
    Last edited by spoggi, Jul 15, 2020
  14. ganons

    ganons GBAtemp Addict
    Member

    Joined:
    Jun 12, 2005
    Messages:
    2,881
    Country:
    Sell it and move on?
     
  15. thenew

    thenew Newbie
    Newcomer

    Joined:
    Feb 25, 2019
    Messages:
    1
    Country:
    France
    @Alramir can i get the info pliz , need 2 buy 2 lite version with dhl thanks
     
  16. The8Darkness

    The8Darkness Advanced Member
    Newcomer

    Joined:
    Feb 18, 2020
    Messages:
    59
    Country:
    Germany
    I have one of the shakiest hands there is (like If I take a spoon full of sugar, I cant move it 2cm without spilling sugar, so I need to either only fill half spoon or use both hands to hold the spoon).
    Even though I got experience soldering small components, I literally need to lay my hand on something so I dont shake from one capacitator to the other - but I have like a "tiny table" that I can put over the thing I solder to have a surface for laying my hand on.
    Shaky hands are an obstacle, not an impossibility. (Also did it without magnification)

    Not saying you should just try it, just saying you could still practice in the future if youre interested in soldering - ofcourse you probably wont become a professional and you shouldnt try to become a surgeon with shaky hands :)
     
  17. Alramir

    Alramir Mainline Injector
    Member

    Joined:
    Jul 6, 2020
    Messages:
    222
    Country:
    United Kingdom
    DM'ed you some details.

    Yeah no plans on surgeon career :D , I did manage soldering my keyboard that I built and have done my Xbox RGH in the past maybe just confidence levels for me rather than ability. :P
     
    thenew likes this.
  18. blawar

    blawar Developer
    Developer

    Joined:
    Nov 21, 2016
    Messages:
    1,624
    Country:
    United States
    This type of work is usually around $60 - 100 / hour, 1 hour minimum by professionals. I can assure you that his elevated prices are well within normal ranges, and is to be expected if he is being flooded with work. I can tell you that I would not even waste my time responding to your PM's for $40, let alone modding and shipping your switch. (I do not mod switch's, please do not PM me).

    — Posts automatically merged - Please don't double post! —

    I solder, just not something I do for people other than friends and family.
     
    caldeio, SonyUSA, DBsss and 1 other person like this.
  19. artosis2

    artosis2 Newbie
    Newcomer

    Joined:
    Jul 15, 2020
    Messages:
    5
    Country:
    Italy
    Hello, I'd like to inquire about the rumored aliexpress vendors, if someone could DM me the details (maybe @Alramir); thank you!
     
  20. Artwebb

    Artwebb Advanced Member
    Newcomer

    Joined:
    Jun 18, 2018
    Messages:
    98
    Country:
    Canada
    I'd chime in as well. He stated price gouging and even put the definition, yet nothing about him raising the prices is price grouging at all. Not sure what world this guy was living on that he thought he would get this done for $40 including shipping back. He stated a price, guess if you wanted that price he should have taken it right then and there. His time is worth more than $20 or so.

    Christ back in the original playstation days it was $60 for a mod, and at that time blank CD's to burn the games were $20 each lol
     
    Thejigmaster likes this.
Draft saved Draft deleted
Loading...

Hide similar threads Similar threads with keywords - Received, Units,