Hacking RHG xbox won't turn on

Demix

Well-Known Member
OP
Member
Joined
Sep 5, 2018
Messages
194
Trophies
0
Age
29
XP
855
Country
United States
So I followed mr Mario how to rhg phat 360 and I got all the way to the point on booting. Just red light showing I got power now, but the xbox itself does not want to turn on. Rechecked connections and I didn't burn anything or break off
 

Attachments

  • IMG_20201108_002753.jpg
    IMG_20201108_002753.jpg
    1.1 MB · Views: 127

DinohScene

Gay boy
Global Moderator
Joined
Oct 11, 2011
Messages
21,520
Trophies
3
Location
Восторг
XP
17,294
Country
Antarctica
Do your wires run near any coils or MOSFETS?
Injected the ECC to glitch to XeLL?
Programmed the chip?

Other things you can try is shortening the RST wire a tiny bit.

Could you post some close up pictures of your solderjob?
Might be helpful.
 

Demix

Well-Known Member
OP
Member
Joined
Sep 5, 2018
Messages
194
Trophies
0
Age
29
XP
855
Country
United States
The power brick is orange, following the video I programmed the chip first and then did 2x nand read. Nothing touching coils and checked usb ports. I can turn off the chip and still won't boot. I can attach to programmer chip and it gets power from the xbox as well. Not sure which points to check, xbox controller also does not power it on
 

Attachments

  • IMG_20201108_071538.jpg
    IMG_20201108_071538.jpg
    1.3 MB · Views: 127
  • IMG_20201108_071603.jpg
    IMG_20201108_071603.jpg
    1.3 MB · Views: 128
  • IMG_20201108_072021.jpg
    IMG_20201108_072021.jpg
    947 KB · Views: 126
Last edited by Demix,

Demix

Well-Known Member
OP
Member
Joined
Sep 5, 2018
Messages
194
Trophies
0
Age
29
XP
855
Country
United States
Double post but FT6U1 came off while looking around, here is the full board view. Looked through all the lines and seems fine
 

Attachments

  • IMG_20201108_103330.jpg
    IMG_20201108_103330.jpg
    1.1 MB · Views: 120
  • IMG_20201108_103341.jpg
    IMG_20201108_103341.jpg
    1.3 MB · Views: 114
  • IMG_20201108_103419.jpg
    IMG_20201108_103419.jpg
    1.2 MB · Views: 114
  • IMG_20201108_103426.jpg
    IMG_20201108_103426.jpg
    1.2 MB · Views: 134
  • IMG_20201108_103503.jpg
    IMG_20201108_103503.jpg
    1.2 MB · Views: 126
  • IMG_20201108_103508.jpg
    IMG_20201108_103508.jpg
    1.3 MB · Views: 125
  • IMG_20201108_103512.jpg
    IMG_20201108_103512.jpg
    1.4 MB · Views: 138
  • IMG_20201108_103515.jpg
    IMG_20201108_103515.jpg
    1.3 MB · Views: 135

fwizbee

Member
Newcomer
Joined
Jan 29, 2016
Messages
12
Trophies
0
Age
25
XP
1,066
Country
Gambia, The
Sorry to say, but this soldering is very very bad...
Short the Cableends they are much to long an secure them....
Otherwise you will rip Pads off pretty soon and your Console is a Brick!
 

Demix

Well-Known Member
OP
Member
Joined
Sep 5, 2018
Messages
194
Trophies
0
Age
29
XP
855
Country
United States
Well, I found the 6v chip broke off a leg in middle and another leg had a small crack in it. I tried soldering a wire to bridge the connection but that didn't work. Soldering bad, but I cleaned up by removing everything, no power, recut the wires smaller and tried to nand dump again. Got can't continue 0000 error multiple times. The power brick did turn red after the successfully attempt, had to unplug the brick and it went back to orange. Anyways it went trash, the consol was very dirty,a and the metal frame had some rust. It cost 10 dollars at thrift store, ordered another rghed already on ebay
 

Attachments

  • IMG_20201110_204745.jpg
    IMG_20201110_204745.jpg
    1.4 MB · Views: 122
Last edited by Demix,
General chit-chat
Help Users
    Ophelia_Later @ Ophelia_Later: lol yeah it would