1. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    I got pretty much new V2 with new board HAD-CPU-01 that doesn't charge with original Nintendo charger
    (i tried 3 chargers same behavior).

    When i plug charger tester shows 5v 0amps, on one side it constantly blinking.
    I checked incoming voltage(before fuse) with original charger it's fluctuate between 1v and 4v.

    Works with 5v power source, also in fast charge mode 5v 1.8apms, no matter what cable side i use.

    Didn't work in docking mode, LED on dock blinking and console still stay active doesn't even turn off the screen.

    Any ideas?

    Thanks!
     
    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  2. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    Board looks like new i inspected it under the microscope:
    found DC to DC on top of M92T36 was a bit chipped.

    Replaced DC to DC + stuff around and M92T36

    No effect. Console behaves exactly the same.

    So question is, who is responsible for passing 15v on the board?
     

    Attached Files:

    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  3. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    Are you asking where the 15 volts comes from, that is present on the dual channel mosfet PP5
     
    Agilato and FXDX like this.
  4. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    Didn't 15V comes from a charger?
    I thought mosfet PP5 just a gate when signal is present it sends it to BQ.
     
    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  5. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    Are you not getting 15 volts on pin 1 of BQ24193 with the charger plugged in?
     
    Agilato and FXDX like this.
  6. Ericthegreat

    Ericthegreat Not New Member
    Member

    Joined:
    Nov 8, 2008
    Messages:
    3,389
    Country:
    United States
    You could try asking in the reswitched discord.
     
  7. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    With 15v charger on one side i have 5v and other fluctuating between 1v and 4v.
    5v charger on both sides shows 5v on coming test pin and consoles charges.

    My guess is when 15v circuit is open something leaking on the ground, because voltage with 15v aren't completly flat it's fluctuating.
     
    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  8. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    Do you get 15 volts on pin 9 of M92T36 with the charger plugged in
     
    Agilato and FXDX like this.
  9. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    Same readings as on incoming test pin before fuse.
    So with 15v charger on one side i have 5v on pin 9 on other voltage fluctuate 1v-4v
     
    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  10. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    I assume you've checked the port inside and checked the pins on the board.

    Double check cc1 and cc2 are soldered correctly on M92T36
     
    Agilato and FXDX like this.
  11. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    All soldered perfectly fine, i tested pins sems to be in tact no shorts in port.
     
    FXDX likes this.
  12. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    Try removing the fuse then test again with the charger plugged in both ways, thats if your getting the same fluctuating voltage on the fuse.
     
    Agilato and FXDX like this.
  13. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    .
     
    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  14. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    With the fuse removed you should have 5 volts on the lower side of the fuse pad.
     
    Agilato and FXDX like this.
  15. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    Without a fuse 5v no fluctuation, fuse replaced, same problem.
     
    Last edited by Agilato, Jan 28, 2020
    FXDX likes this.
  16. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    So you get a steady 5 volts from both sides of the cable on the fuse.
     
    Agilato and FXDX like this.
  17. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    Yes.
     
    FXDX likes this.
  18. Pintglass

    Pintglass GBAtemp Fan
    Member

    Joined:
    Jan 28, 2019
    Messages:
    364
    Country:
    United Kingdom
    What voltage do you get on cc1 and cc2 of M92T36 with the charger plugged in, try it both ways.
     
    Last edited by Pintglass, Jan 28, 2020
    Agilato and FXDX like this.
  19. Agilato

    OP Agilato GBAtemp Fan
    Member

    Joined:
    Jun 21, 2019
    Messages:
    331
    Country:
    United States
    I know it doesn't make sense... i was checking voltages and got 15v on test pins and cc1/2
    It quiet surprised me because after fuse replacement it behaved same way, i retested few times and 15v there....
    I assembled console and it's changing now...
    From point where i was, we just replaced a fuse...
    It's even docking now.

    I have one guess that fuse was not able to pull needed current... or someone around got needed re-flow...
     

    Attached Files:

    Last edited by Agilato, Jan 28, 2020
    vastrolorde and FXDX like this.
  20. FXDX

    FXDX GBAtemp Regular
    Member

    Joined:
    Sep 15, 2019
    Messages:
    279
    Country:
    Dominican Republic
    That's really good news bro:switch:
     
    Agilato likes this.
Draft saved Draft deleted
Loading...

Hide similar threads Similar threads with keywords - Nintendo, original, charger