1. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    If the demand is there then yes.

    But SX Pro is the same as the others more or less.

    Would many people strip one and fit it internally?
     
  2. Sasori

    Sasori GBAtemp Addict
    Member

    Joined:
    Jan 28, 2015
    Messages:
    2,205
    Country:
    United States
    Considering that a lot of people have one laying around already I would think so. You don't need to strip much off of it to get it to fit
     
  3. djvj

    djvj Member
    Newcomer

    Joined:
    Jan 23, 2016
    Messages:
    35
    Country:
    United States
    So when I inject the payload from tcm gui now, I get "injecting payload" for about 20-30 seconds, then get a green check and no message. Nothing shows on the switch and red led keeps blinking on mod. It used to go solid when the payload injected properly. I've tried reinstalling the driver and still same.

    Ah, got it, had to press button on mod a few times and it took, I'm back in hekate.

    Pressed power button to boot, after error about SD card, got error:
    Unknown package1,
    Version (= '').
    Failed to launch firmware.
     
    Last edited by djvj, Oct 16, 2018
  4. olku

    olku Advanced Member
    Newcomer

    Joined:
    Oct 31, 2015
    Messages:
    72
    Country:
    Estonia
    We don't have to.
    I had to use very thin double sided tape in order it to fit without leaving a bump on the back cover.
    20180812_202413.jpg
     
    Last edited by olku, Oct 16, 2018
  5. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    Eject SD card. Let hekate boot with its default config
     
  6. djvj

    djvj Member
    Newcomer

    Joined:
    Jan 23, 2016
    Messages:
    35
    Country:
    United States

    SD card was never in it. Your previous post said to leave it out so I never put it back in.

    What firmware is it looking for that is failing?
     
    Last edited by djvj, Oct 16, 2018
  7. Sasori

    Sasori GBAtemp Addict
    Member

    Joined:
    Jan 28, 2015
    Messages:
    2,205
    Country:
    United States
    @mattytrog The OP says not to remove anything, but there does not seem to be enough space on my trinket m0 for the rebug file.

    This is the correct file I need to boot into sxos and whatever other payloads I have on my SD right?

    [​IMG]
    [​IMG]

    EDIT: If this happens to anyone else..just double click the reset button twice(fast) twice more.
     
    Last edited by Sasori, Oct 16, 2018
  8. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    Circuitpy is not the drive you need. Double press reset, that should change to trinketboot.

    Then drag the file over.
     
  9. Sasori

    Sasori GBAtemp Addict
    Member

    Joined:
    Jan 28, 2015
    Messages:
    2,205
    Country:
    United States
    Looks like you got me right before the edit.

    The drive seems to be closing when I drag the file over now and if I open it again by double clicking the rebug UF2 is not saved to the drive
     
  10. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    That's the correct behaviour. The drive will disappear once a new UF2 goes on to it.
     
  11. Sasori

    Sasori GBAtemp Addict
    Member

    Joined:
    Jan 28, 2015
    Messages:
    2,205
    Country:
    United States
    Ah, so than whatever is called "current.UF2" now is in fact that rebug one?
     
  12. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    Current.uf2 is exactly that.

    Currently what is on the chip.

    Drag something else over on to it, the drive will disappear. Now whatever you have just dragged over is now the current.uf2.

    The cycle continues
     
    Sasori likes this.
  13. ciariello

    ciariello Newbie
    Newcomer

    Joined:
    Sep 6, 2018
    Messages:
    7
    Country:
    Italy
    Why did you cut the backplate?
     

    Attached Files:

  14. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    Normally you cut the backplate to stop the reset button being so easy to press...
     
  15. ciariello

    ciariello Newbie
    Newcomer

    Joined:
    Sep 6, 2018
    Messages:
    7
    Country:
    Italy
    fortunately never had this problem
     
  16. djvj

    djvj Member
    Newcomer

    Joined:
    Jan 23, 2016
    Messages:
    35
    Country:
    United States
    Hi Mattytrog, do you know what firmware it's referring to, so hopefully I can get something figure out why I can't boot to home screen still?
     
  17. Sasori

    Sasori GBAtemp Addict
    Member

    Joined:
    Jan 28, 2015
    Messages:
    2,205
    Country:
    United States
    I'm having trouble soldering to the micro b connector on the trinket m0 for RX and TX. Can I just solder to the specified TX and RX points on this trinket instead ? Iirc they are on the left hand side
     
  18. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    Ok...

    OK... We seem to be struggling with this. It`s OK... It is different from other modchips you may have used.

    Follow this... Leave SD card out of machine

    1) Boot up TegraRCMsmash
    2) Get ready to send Hekate
    3) Get into RCM
    4) Send Hekate. This should take you to the Hekate menu
    5) Select launch with power buttons... You will get an error about SD card missing and booting default configuration.
    6) Switch should boot normally
    7) Once on home screen of switch, disconnect from USB
    8) Press reset on modchip/switchme/trinket TWICE!!! I forget which you are using.
    9) Plug into your PC. REBUGBOOT/ TRINKETBOOT should pop up
    10) You will see 3 files in there: CURRENT.UF2, INDEX.HTM & INFO_UF2.TXT
    11) If you don`t see the above in step 10, then keep trying until you do. Keep the drive open. No need to delete anything
    12) Download THIS
    13) Unzip.
    14) Drag the file that is called S2_Chainloader (ends in UF2) to the REBUGBOOT / TRINKETBOOT drive
    15) Insert SD card into PC. In the file you have downloaded, you will find a 0.zip file
    16) Extract this
    17) Put the new extracted 0 folder on to your memory card
    18) Download hekate.bin from the hekate thread. Place hekate.bin INSIDE the 0 folder.
    19) Rename hekate.bin to start.bin
    20) Power off switch with power button, insert SD card and try to boot.
     
    djvj likes this.
  19. Sasori

    Sasori GBAtemp Addict
    Member

    Joined:
    Jan 28, 2015
    Messages:
    2,205
    Country:
    United States
    Looks like it is working! Woot woot

    Just need to rearrange my SD card for SXOS now it looks like since it yells at me when I click Launch about no configs being found
     

    Attached Files:

    Last edited by Sasori, Oct 17, 2018
  20. mattytrog

    OP mattytrog You don`t want to listen to anything I say.
    Member

    Joined:
    Apr 27, 2018
    Messages:
    3,700
    Country:
    United Kingdom
    Well done.

    But please please shorten those wires A LOT! The heatpipe gets very hot.
    Please reroute your cables correctly
     
Draft saved Draft deleted
Loading...

Hide similar threads Similar threads with keywords - ItsyBitsy, Internal, (Trinket