Homebrew Question i killed my switch by doing choidujour pc. What parts would i have to get replaced for it to work

[Deleted User]

So i like killed it and i want to know what i would need to replace like the motherboard or the emmc module. I followed this guide https://switch.homebrew.guide/usingcfw/manualchoiupgrade but since im a total retard i screwed something up

 

[Hayato213]

How you killed it, what component you killed?

 

[Dark Ronin]

Replace console.
Seriously here, if you're looking for help, you should describe your situation much clearer than this "lmao I broke smth idk help ahaha".

 

[Deleted User]

I was asking in general like if you like screw up something in your NAND what would you have to replace

 

[lembi2001]

How have you screwed it up though??

It could be a simple fix but it could be a complicated fix.

You have given no indication as to what you have done or what leads you to believe it is .

Impossible to help you without this information

 

[Hayato213]

It is more like you software bricked, than actually killing a switch, if you can get into RCM mode then it mean it is not bricked. You should be more clear and you should mention the fact that you attempted to downgrade from 8.1.0 to 1.0.0 when you used ChoidujourNX.

 

[Dark Ronin]

Why would you mess with choidujour for PC in a first place?

 

[Deleted User]

Yeah that was with Choi nx yesterday. Today i tried doing the Choi PC guide to get to 6.00
I don't get past Kosmos bootlogo

 

[Hayato213]

Yeah that was with Choi nx yesterday. Today i tried doing the Choi PC guide to get to 6.00
I don't get past Kosmos bootlogo

So did you managed to reflash 6.0 firmware and it didn't work, try to go to 5.1.0 see if it boot.

 

[lembi2001]

So reading previous posts on another thread, you downgraded to 1.00 after running 8.1.0 OFW.

Your fuse count is now 10 and you are stuck at a lower firmware?

Why not just install the latest OFW directly using Safe Mode:

• With the system powered off, press and hold Volume Down;
• Press the Power button while still holding Volume Down;
• Keep pressing the Power button, but let go of Volume Down and press and hold Volume Up;
• Let go of the Power button and keep holding Volume Up until the safemode system module starts.

This results in the system booting the safemode sysmodule and automatically finding and installing new updates from the internet.

Once you have done this your console should boot then you can use AutoRCM again to boot CFW

 

[Dark Ronin]

Hey, do we look like a mind readers to you?!
1. What was your console initial state?
2. What exactly have you done?
3. What state is it now?
Be more damn cooperative or gtfo already.

 

[EmulateLife]

Hey, do we look like a mind readers to you?!
1. What was your console initial state?
2. What exactly have you done?
3. What state is it now?
Be more damn cooperative or gtfo already.

Calm down geez

 

[lembi2001]

Hey, do we look like a mind readers to you?!
1. What was your console initial state?
2. What exactly have you done?
3. What state is it now?
Be more damn cooperative or gtfo already.

It's as if he doesn't want help. I dug through his previous posts and gleaned that he was on 8.1.0 OFW and for some mental reason tried to downgrade to 1.0.0

 

[Dark Ronin]

It's as if he doesn't want help. I dug through his previous posts and gleaned that he was on 8.1.0 OFW and for some mental reason tried to downgrade to 1.0.0

Yeah, with no proper backup probably.

--------------------- MERGED ---------------------------

Calm down geez

I'm perfectly calm. He just get treatment he's looking for, that's all.

 

[lembi2001]

This thread is the equivalent of taking your car to a mechanic and saying it's broken, how do i fix it?

 

[DSoryu]

Calm down geez

Nah it's ok, OP is a complete noob that doesn't give a fuck about correct procedures or basic instruction following, this is the third thread he makes asking for help, providing zero information, and though people want to help him, he always does the complete opposite of what he should do or doesn't do anything at all.

I bet you that his next post will be something like: "Question: I revived my switch but downgraded again to 1.0 for no reason now switchz wont turn on somebody help plz"

 

[Deleted User]

ok revived switch surprisingly worked thanks hayato213

 

[The Real Jdbye]

ok revived switch surprisingly worked thanks hayato213

Not that surprising. You can't hardbrick a Switch just by messing with firmware.

 

[ZachyCatGames]

So reading previous posts on another thread, you downgraded to 1.00 after running 8.1.0 OFW.

Your fuse count is now 10 and you are stuck at a lower firmware?

Why not just install the latest OFW directly using Safe Mode:

• With the system powered off, press and hold Volume Down;
• Press the Power button while still holding Volume Down;
• Keep pressing the Power button, but let go of Volume Down and press and hold Volume Up;
• Let go of the Power button and keep holding Volume Up until the safemode system module starts.

This results in the system booting the safemode sysmodule and automatically finding and installing new updates from the internet.

Once you have done this your console should boot then you can use AutoRCM again to boot CFW

Safe mode won’t work on a system with too many fuses burnt

 

[lembi2001]

Safe mode won’t work on a system with too many fuses burnt

Good to know, thanks for telling me