FALCON RGH 1.2 CREATE ECC (NO PROBS) WRITE ECC TIMEOUT ALL?

Discussion in 'Xbox 360 - Hacking & Homebrew' started by vstar950, Jun 28, 2018.

  1. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    Falcon Manually Selected
    ECC created
    Version: 10
    Flash Config: 0x01198010
    Writing Nand
    image_00000000.ecc
    Error: 280 writing block 0
    Error: 680 writing block 1
    IoTimedOut
    Error: 601 writing block 2
    IoTimedOut
    Error: 623 writing block 3
    IoTimedOut
    Error: 621 writing block 4
    IoTimedOut
    IoTimedOut
    Error: 623 writing block 6
    IoTimedOut
    Error: 623 writing block 7
    IoTimedOut
    Error: 621 writing block 8
    IoTimedOut
    Error: 621 writing block 9
    IoTimedOut
    Error: 623 writing block A
    IoTimedOut
    Error: 621 writing block B
    IoTimedOut
    Error: 621 writing block C
    IoTimedOut
    Error: 621 writing block D
    IoTimedOut
    Error: 621 writing block E
    IoTimedOut
    Error: 623 writing block F
    IoTimedOut
    Error: 623 writing block 10
    IoTimedOut
    Error: 621 writing block 11
    IoTimedOut
    Error: 001 writing block 12
    IoTimedOut
    Error: 623 writing block 13
    IoTimedOut
    Error: 621 writing block 14
    IoTimedOut
    Error: 621 writing block 15
    IoTimedOut
    Error: 621 writing block 16
    IoTimedOut
    IoTimedOut
    Error: 623 writing block 18
    IoTimedOut
    Error: 621 writing block 19
    IoTimedOut
    Error: 001 writing block 1A
    IoTimedOut
    Error: 623 writing block 1B
    IoTimedOut
    Error: 623 writing block 1C
    IoTimedOut
    Error: 621 writing block 1D
    IoTimedOut
    Error: 621 writing block 1E
    IoTimedOut
    Error: 621 writing block 1F
    IoTimedOut
    Error: 001 writing block 20
    IoTimedOut
    Error: 001 writing block 21
    IoTimedOut
    Error: 621 writing block 22
    IoTimedOut
    Error: 621 writing block 23
    IoTimedOut
    Error: 621 writing block 24
    IoTimedOut
    Error: 621 writing block 25
    IoTimedOut
    Error: 621 writing block 26
    IoTimedOut
    Error: 621 writing block 27
    IoTimedOut
    Error: 623 writing block 28
    IoTimedOut
    Error: 621 writing block 29
    IoTimedOut
    Error: 621 writing block 2A
    IoTimedOut
    Error: 623 writing block 2B
    IoTimedOut
    Error: 623 writing block 2C
    IoTimedOut
    Error: 623 writing block 2D
    IoTimedOut
    Error: 223 writing block 2E
    IoTimedOut
    Error: 001 writing block 2F
    IoTimedOut
    Error: 621 writing block 30
    IoTimedOut
    Error: 621 writing block 31
    IoTimedOut
    Error: 623 writing block 32
    IoTimedOut
    Error: 621 writing block 33
    IoTimedOut
    Error: 002 writing block 34
    IoTimedOut
    Error: 621 writing block 35
    IoTimedOut
    Error: 621 writing block 36
    IoTimedOut
    Error: 623 writing block 37
    IoTimedOut
    Error: 623 writing block 38
    IoTimedOut
    Error: 621 writing block 39
    IoTimedOut
    Error: 621 writing block 3A
    IoTimedOut
    Error: 621 writing block 3B
    IoTimedOut
    Error: 623 writing block 3C
    IoTimedOut
    Error: 623 writing block 3D
    IoTimedOut
    Error: 623 writing block 3E
    IoTimedOut
    Error: 621 writing block 3F
    IoTimedOut
    Error: 623 writing block 40
    IoTimedOut
    Error: 623 writing block 41
    IoTimedOut
    Error: 623 writing block 42
    IoTimedOut
    Error: 623 writing block 43
    IoTimedOut
    Error: 623 writing block 44
    IoTimedOut
    Error: 621 writing block 45
    IoTimedOut
    Error: 621 writing block 46
    IoTimedOut
    Error: 621 writing block 47
    IoTimedOut
    Error: 623 writing block 48
    IoTimedOut
    Error: 623 writing block 49
    IoTimedOut
    Error: 623 writing block 4A
    IoTimedOut
    Error: 621 writing block 4B
    IoTimedOut
    Error: 623 writing block 4C
    IoTimedOut
    Error: 621 writing block 4D
    IoTimedOut
    Error: 621 writing block 4E
    IoTimedOut
    Error: 621 writing block 4F
    Done!
    in 1:27 min:confused:ec
    WHAT GIVES? NO CROSSED WIRES AND FOLLOWED THIS VIDEO on youtube
    /watch?time_continue=8&v=UephTE0nASg
    i got this from hitting the question mark next to motherboard type
    WARNING! - Your selected working directory already contains files!
    You can view these files by using 'Show Working Folder' Button
    Connection Error
    Checking Files
    Connection Error
    Checking Console..
    Version: 10
    Flash Config: 0x01198010
    Error: 251 reading block 0
    IoTimedOut
    IoTimedOut:No more bytes!
    01198010
    Xenon, Zephyr, Opus, Falcon
    THESE ARE PICS OF MY JR PROGRAMMER SOLDER POINTS in mediafire
    com/view/kp1doz6ttj3azt6/20180627_223625.jpg/file
    com/view/9ixhk1s75mvk0i5/20180627_223633.jpg/file
    com/view/7lkq4b77z4a1psg/20180627_223654.jpg/file
    i created an ecc (worked) then tried to write an ecc then it timed out on all blocks. so i closed jrunner program opened it up again thinking the program was the problem. then tried to create ecc but it a asks to select a file. i am confused.
    the console will not power on anymore
    i am trying to write the retail nand but when u click write nand i select falcon then i continue. and nothing. all reads and dumps were text book until trying to write ecc. i have double back ups of originals.
     
  2. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Did you try unplugging the programmer or pressing the power kill button on the side? And if you don't mind, please upload the solder pics as thumbnails. Usually these issues have to do with soldering, but the programmer or Jrunner can freeze up or glitch every once in awhile. If you read the nand and it decrypted the flash config, then something is going on now that wasn't happening before. Also, was the programmer drivers and required files installed correctly?
     
    Last edited by brickmii82, Jun 29, 2018
  3. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    yes they were installed correctly. (drivers). solder points are good. i did unplug the programmer. when i want to read the ecc it asks for me to select a file. i have no clue what file. so i am stuck there. I really dont want to mess this falcon up. so i have put it on hold for a while till i find a modder or can get a step by step noob proof from this point on. this 360 looks and smells new. not a hairline scratch or single smudge. that is why I dont want to brick this board. i already have twice but brought it back by reflashing the retail nand. (thank God) each time i read the ecc then write the ecc it bricks it and time to reflash it. i cannot figure it out.
     
  4. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Well, I still would like some thumbnail pics of the soldering and setup, and idk what video you're going by, but in order to help I/we need information. We can't magically discern what the problem is. Are you leaving the xbox plugged in for the ecc flash? Why are you trying to read the ECC? Also, the only file I could see you needing to select is the falcon.ecc file. Pics would help a lot.

    Try using this with the Advanced tab up top. Select custom nand/cr functions, write, 16, and unzip this and browse to it then write it.
     

    Attached Files:

    Last edited by brickmii82, Jul 3, 2018
  5. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    i am following this youtube video.

    watch?v=UephTE0nASg&t=8s

    The ecc was just following this tutorial.

    the console is plugged in and not powered on.

    now when i read the ecc it asks for me to select a file. makes no sense because it just read from the console before

    pics as followed MEDIAFIRE
    CANT PUT LINKS DUE TO STUPID RULES ( my links are spam)

    btw i thank you for hanging in with me.

    i have been told by modders that my beta 7 jrunner program could b the issue, since there was a buggy version out there.
     
    Last edited by vstar950, Jul 5, 2018
  6. tbb043

    tbb043 Member

    Member
    8
    Jan 30, 2008
    United States
    I'm so glad I paid someone to install the jtag for me on my falcon many moons ago. No offense, but this seems like such a hassle, meanwhile mine's been running like a charm for a decade or so. Hope you get your issues sorted out.
     
  7. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Go look through the RGH 1.2 section I put in the How to hack your 360 thread sticky. See if anything sounds different or if any pics there help.
     
  8. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    LOL. my ps2 fmcb mod was a pain when it should have been easy as pie. now i never need the forums on that because of so many man hours custom configuring things.

    — Posts automatically merged - Please don't double post! —

    can you link me a good working copy of jrunner software? i am on beta 7. and it is a mess. (BTW) thank you for your hack a 360 tutorial. I am reading it now.
     
  9. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Last edited by brickmii82, Jul 6, 2018
  10. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    i must be blind i dont see anything talking about beta 8.
     
  11. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Updated my last post with links. Also, you have the RGH 1.2 timing files right?
     
    Last edited by brickmii82, Jul 6, 2018
  12. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    Btw i have that matrix 3. do i not solder the 3.3v and pll? and do i cross the solder pads on top for the fat(matrix 3)? thank you for the links
     
    Last edited by vstar950, Jul 6, 2018
  13. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    A
    All of the solder points are in the guide. Does the Matrix chip have a kinda big rectangular metal piece? Thats the clock if it does, and you'll need to disable it. Other than that, I can't think of anything else you might have trouble with.
     
  14. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    after the ebay dot com paste this and this is the dude i have
    /itm/Matrix-Glitcher-V3-9-6A-X360-Corona-48MHZ-Crystals-Big-IC-Chip/123147586858?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2648

    your help REALLY MEANS ALOT TO ME.
     
    Last edited by vstar950, Jul 6, 2018
  15. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Yep it has a crystal clock. You’ll have to remove that 0 ohm resistor up and between D and E. Can you try going through step by step with the guide we have here otherwise? I think I wrote it pretty understandibly. Also, you can upload pics straight onto your posts with the upload a file option.
     
  16. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    thanks again. ill get on it
     
  17. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    somebody was saying i could just avoid soldering the pll point on chip instead of floating that resistor. is this true?
     
  18. brickmii82

    brickmii82 GBAtemp Maniac

    Member
    9
    Feb 21, 2015
    United States
    Nope its false. Thats what slows down the cpu.
     
  19. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    wow. this is why i get so worried doing this. these people that know everything about nothing. THANKS AGAIN DUDE.
     
  20. vstar950
    OP

    vstar950 Advanced Member

    Newcomer
    2
    Jun 28, 2018
    United States
    where it shows that you bridged the matrix, is that the left green line i did or the right or both?
     

    Attached Files:

Quick Reply
Draft saved Draft deleted
Loading...