after system update FSD will not load only normal dash

Discussion in 'Xbox 360 - Hacking & Homebrew' started by Bill Balss, Jun 23, 2014.

  1. Bill Balss
    OP

    Bill Balss Newbie

    Newcomer
    3
    0
    Jun 23, 2014
    United States
    Like the title says. I updated to 47 using XeBuild and then NAND Flasher. The updated dash now allows for COD Ghosts to play on normal dash but FSD no longer loads up. When turning on the FSD it loads directly to normal dash. I also cannot get an FTP connection between my computer and the XBox. Is normal dash harder to connect to computer for FTP? Would the system update have changed my launch.ini? If so, or whatever else, how can I restore this?

    I checked the system settings on the normal dash and have verified the 47 installed.

    I have original NAND dump and the new one for the 47.

    Thoughts?

    Jasper 16

    FSD is a 3.0 775 I believe.

    For whatever it is worth here is my back up launch.ini file, but I no longer have access to it.

    [QuickLaunchButtons]
    BUT_X = Hdd:\XellLaunch\default.xex
    Default = Hdd:\FSD\default.xex
    [Settings]
    nxemini = true
    pingpatch = true

    Please advise. and thanks bunches.
     
  2. hundshamer

    hundshamer GBAtemp Advanced Maniac

    Blacklisted Trader
    1,810
    806
    May 22, 2009
    United States
    Did you update Dashlaunch? You may need to burn XeXMenu to DVD if you do not have access to it. I personally put a shortcut in the XeXMenu folder c0de9999 folder so you have access to FSD from the NXE menu.
     
  3. mickcris

    mickcris Advanced Member

    Newcomer
    54
    13
    Nov 15, 2006
    United States
    You probably need to install dashlaunch. You probably forgot to add it to your new NAND.
     
  4. Bill Balss
    OP

    Bill Balss Newbie

    Newcomer
    3
    0
    Jun 23, 2014
    United States
    OK yes I def did not add it to my new nand. I do have dashlaunch on the internal xbox HDD. Should I just use the xboxUSB the dashlaunch over to the internal HDD again? I got the box jtagged already and have been working my way through all this. I do not know everything but I have been poking around. With a few pointers I should be able to make this happen. I used to FTP all the time from FSD.

    Thanks for any additional steps/instructions you may have.

    I will say that the "include DashLaunch" was checked but only if dashlaunch is internal to XeBuild if I needed to place the dashlaunch program into this program in anyway way I did not do that.
     
  5. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,651
    12,053
    Oct 11, 2011
    Antarctica
    В небо
    Follow this tut and you'll be fine again.
    Note that you should replace the location of FSD with the location on your HDD if it's not in the same folder.
     
  6. Bill Balss
    OP

    Bill Balss Newbie

    Newcomer
    3
    0
    Jun 23, 2014
    United States
    ok Failure, now the XBox boots up but only to a black screen. I did the new system update via USB using XELL and the eject button. The screen said success and to power down. I left the box unplugged for a few min then turned it back on...only black screen now.

    I had to place a xenon.elf file in the root along with the update bin. Is the xenon.elf file supposed to be a perfect match or does anyone work? The links to get raw flash from - http://www.libxenon.org/ no longer work so I sed the one I had.

    I then placed an older dash on the usb drive to try to revert, now Xell won't even boot up.

    thoughts?
     
  7. DinohScene

    DinohScene Dino May Fire

    Member
    GBAtemp Patron
    DinohScene is a Patron of GBAtemp and is helping us stay independent!

    Our Patreon
    15,651
    12,053
    Oct 11, 2011
    Antarctica
    В небо
    Have you got an hardware flasher hooked up to it?
    If not then let a modshop reflash it for you.
    If XeLL doesn't boot then your NAND is most likely corrupt.