Search results

  1. S

    "New" Hwfly OLED/Core V5 Chip is Out on Aliexpress

    Hey @randy_w Does this one look okay to you v4.1 OLED (if not, do you have a link to an official one I should get?) I don't want to deal with the clones if possible. https://www.aliexpress.com/item/1005004276175281.html Thanks heaps!
  2. S

    Hardware Basic Repair Guide of Current EZ-FLASH Products

    @EZ-Flash2 keep getting S71 read error on Omega DE, hot air reflow worked a few times but now it doesn't work anymore. I reballed it and reapplied it and still S71 read error. Any recommendations on where i can get a replacement S71 chip?
  3. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I've done a few switches for myself and mates too. I put double sided tape on the chip to secure it to the shield (to prevent any type of short) then epoxy on the chip to secure it to the shield as well. However i also dab a bit along the wires to secure them to the mainboard, preferably near...
  4. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    What are you on about mate? Maybe you should read it properly instead. He say's it wont stick long term if you put epoxy on the shield, he is not recommending to put the epoxy on the shield itself. And says if your soldering quality is good enough, then you don't need any type of glue. He also...
  5. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    During installation of course. But post install, that tape isn't going to hold at all once it starts getting warm inside the switch. Infact it might peel off and end up in the fan or something. If he's not confident in the wires holding, then epoxy is best. Matty says so himself in his first...
  6. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Good job mate, but the tape will not hold at all, use some epoxy and dab a bit on the wires and glue them to the board (don't glue your connections, just the wire)
  7. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Brilliant, thanks mate! Have ordered a bunch of different ones from that link i pasted before, in case I mess them up. Any tips/suggestions on soldering these tiny little f***s haha? @mattytrog there wasn't an alternate USB disconnect strap point by any chance?
  8. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Legend!! Thanks mate! EDIT: Found an old post of yours with an attached schematic here showing the resistors: https://gbatemp.net/threads/components-used-on-the-switch-mostly-the-motherboard-and-main-console.525026/#post-8411401 Will order some resistors, but looks like i can only get THICK...
  9. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Cheers mate, I think the resistor underneath is fine, it's just the missing resistor on the right. Switch still seems to boot to hekate, haven't tried booting to horizon yet. Do you know which resistor i need to replace it with?Any repercussions if i just bridge the joint?
  10. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Hi @mattytrog Just received a switch that someone tried and failed modding, was wondering if you can tell me the best way to fix this? Resistor has been desoldered and that usb pad has been lifted. (this is the next to the USB disconnect strap). Are you able to advise OHMs or part number I'd...
  11. S

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Yep all good, i only want hekate so i normally disable mode change anyways. Was no errors during sketch compile/upload so ill try updating the arduino tools+libs and see if that fixes it. I just tried loading in the precompiled uf2 and it works 100%, definitely something to do with my setup...
  12. S

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Cheers mate, ill give it another shot tomorrow and report back
  13. S

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Arduino IDE did tell me I have some board/tools updates which I didn't do, so you might be right, maybe ill try those and try again, or maybe ill try upload via visual studio. Also just want to clarify, is this the correct boot process or is something messed up here? Hekate bootlogo -> Sept...
  14. S

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    I cloned your github, opened the source code in arduino ide, commented all chips except for trinket_rebug and uploaded the sketch.
  15. S

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Updated switchboot part 1 & 2 to 1.20 (old version was working fine), now switch wont boot. Stuck at blank screen, can't get trinket to connect to pc for reflashing now either. Pressing vol+ on the blank screen does make the LED turn on (i have all straps fitted). Pc wont even recognise that...
  16. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Looks to me you didn't clip in the sd card slot back in properly? No SD card is detected in the switch. Also you're missing the hekate sleep mode libraries (or could be because your SD card slot is not clipped in properly as well): https://github.com/CTCaer/hekate/releases Grab the latest...
  17. S

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Hi Matty, Can you please upload FlashStorage.h to git or link it here? Can't compile/push sketch manually via arduino without it. https://github.com/cmaglie/FlashStorage/blob/master/src/FlashStorage.h Is this the one you used? Cheers
  18. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I noticed i can only flash chip when switch is in sleep mode, try putting in sleep mode then connecting to pc.
  19. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    @mattytrog Hey Matty, thanks for all your posts so far appreciate it. I have a question that might be slightly off topic. Is it possible for us to design and print a custom pcb with a "lego connector" that would plug into the EMMC slot, that would allow us to attach two EMMC/NAND chips at...
  20. S

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    @mattytrog This might be a dumb question, but for the joycon strap you've circled two pads, do I choose any of those pads or am i meant to bridge them? Cheers.
General chit-chat
Help Users
  • No one is chatting at the moment.
    ButterScott101 @ ButterScott101: +1