Search results

  1. R

    Installing large XCI

    Yes, you can.
  2. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    You don't need to do it if you don't want but I think that you need a better printer to make a better fake cover.
  3. R

    Picofly AIO Thread

    If you have 2.5 you can't flash with pikotool.
  4. R

    Picofly AIO Thread

    I tried a lot of things and still have the problem wht the boot0/boot1 and slow mode of the emmc. I maked a emummc and can launch HOS from it. Is dangerous to leave it at this for the moment? I'm really tired and want to rest.
  5. R

    Picofly AIO Thread

    I replaced the wires with new ones shorted and now is worst, when I try to launch HOS with vol+ and vol- mpt sjpw amything at all except one time that show pink screen. It is possible that i damaged the emmc? Edit: I mounted the emmc in windows with hekate and can see the content and appear to...
  6. R

    Picofly AIO Thread

    Is strange, now I get this error when I try to launch HOS from hekate, I tried earlier and worked. I'm using 2.64 firmware in a fresh install. If I desolder the Dat0 the conosle launch hos without problem.
  7. R

    Picofly AIO Thread

    Ok, is all installed and get the no sd card screen but I have a problem, if I boot with vol- + vol+ to boot stock the console get stuck in a black screen after the nintendo logo.
  8. R

    Picofly AIO Thread

    Oh right, is a mariko normal (no oled no lite) @rehius that is not an option now because I have 3 points in the emmc now and to solder in the connector I would need to remove the emmc
  9. R

    Picofly AIO Thread

    Any other alternative point for th3 3.3v? I used the one from the emmc but it has come loose and I don't want to remove the emmc again so as not to lose the reset too and the one next to the memories is difficult because I have the chip right next to it.
  10. R

    Picofly AIO Thread

    I have a doubt about the 3.3v in the emmc board, in the picture appear to be shorted is that correct?
  11. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    19,5 Ohm with the lowest resistance. Is a relieve because I had a lot of problem soldering the second mosfet. Thank you
  12. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Anyone with the cpu flex can tell me what value get the multimeter in continuity mode in the solder points? To check if I have solder mine well. I get 0001 and 0015 in the two points of the two mosfets
  13. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    No, the upgrade feature was added in the 2.6 version.
  14. R

    Homebrew WIP [Official] switch-lan-play

    ldn.mitm convert the ad-hoc (connection between consoles without using a lan) to a lan connection. Without it you can't use lan-play in some games.
  15. R

    Unpatched Switch Not Going Into Recovery Mode

    You don't need to change SD, PC,, USB etc you don't need any of this to enter to rcm you need it to send the payload. Check if the vol+ works in HOS and if the joycon is recognied attached (to discard a problem with the rail) It doesn't matter, patched switches can enter to rcm too.
  16. R

    Story of Seasons: A Wonderful Life (English Patch)

    The passwords is in the message that you quoted.
  17. R

    After 16.0.0 switch won't boot past load screen

    Check the titleid in the error screen and go to the folder atmosphere/contents in the sdcard check if you have a folder with that titleid and delete it.
  18. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    The dat0 is used for glitching or is only needed to modify the emmc? If its the second what would happend if we edit the boot0 with the bootloader of hwfly and then remove the dat0 from the chip?
  19. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    I didn't check the firmware progress because is very out of my the firmware in the page 34 is also encrypted? All the progress I see about the investigation of the firmware is about the one with the serial. Why? There would be no differences. The problem is the corruption of the keyblob,
  20. R

    Looking for a certain payload

    You can update all from hekate.
General chit-chat
Help Users
    realtimesave @ realtimesave: got a mig switch here, freshly smuggled in from China