Hardware Components used on the Switch (mostly the motherboard and main console)

jkyoho · Jan 30, 2021

de9ed said:
while this thread sugge

I use mcz for the v1 board as well. v2 board has way smaller size than v1. And I found out NFG0QHB372HS2D fit well for the right1/last(sbu1/2) filter and the 4 other TX/RX filter for v2 I pick DLM0NSM900HY2D

And for v2 board hdmi common mode choke filter alternative(Panasonic)
4x left TX/RX can use -- EXC-14CT900U
right1/last 1(sbu1/2) can use -- EXC-X4CT900X

Alfixes · Jan 31, 2021

justaplaneguy0 said:
I'm working on a nintendo switch and trying to identify 2 components. I am reflowing and cleaning the BCM4356, and blew these 2 components off the board. 1 of them is an IC of some sort, the other I believe is a cap or an inductor. Could someone please help me identify these components so i can order them either from mouser or digikey?

Thank you in advance!

This is a closeup of the two components i'm trying to identify.
View attachment 239670

This shows the exact location of the board I'm working on zoomed out.
View attachment 239671

Bino · Feb 7, 2021

Hey gang, happy to see this kinda thread exists. Anyone able to tell me what these two might be? It's right above where the micro SD car clips in.

Got this is a repair from a bad shop, hoping i can get it working again.

jkyoho · Feb 8, 2021

Bino said:
Hey gang, happy to see this kinda thread exists. Anyone able to tell me what these two might be? It's right above where the micro SD car clips in.

Got this is a repair from a bad shop, hoping i can get it working again.

THOSE are two caps
from top to bottom measured:
5uf
250nf
(10k ohm)
try slight larger value since I measure from a crappy donor board, cap value may shift

Desalvation · Feb 8, 2021

Good afternoon, I have a problem with the left joycon, when it is installed in the switch, it only shows charging, but in the portable mode the console does not see it, it shows that it is connected only via bluetooth. What could be the problem?

Bino · Feb 8, 2021

jkyoho said:
THOSE are two caps
from top to bottom measured:
5uf
250nf
(10k ohm)
try slight larger value since I measure from a crappy donor board, cap value may shift

Thanks! Really appreciate it.

RedViking · Feb 20, 2021

I'm working on fixing my switch (managed to knock loose a part and can't find it). The port is circled, Without it my fan runs wide open anytime the screen is on. Does anyone know what it is?

MeoWStraY · Feb 22, 2021

Hi, I am currently trying to fix my switch after it fell in water. For now the tablet itself works fine, but has no backlignt and some troubles with toutch screen. After checking the board we found one component that is not working at all, if I understood correctly it is in the backlight circut, but I have no idea what it is. If someone can provide me links where I can buy a replacment or just info to feagure what that component is that it would be very nice.

Alfixes · Feb 24, 2021

Hi, it's inductor and should have continuity. I dont know exact value but you can possibly have problem with nearby diode too of inductor gone.

Scottedontknow · Mar 4, 2021

Here's one for you all! So I bought a lot of broken switches..... most of them are the usual issues (usb port, shorted chip somewhere) but this one..... is kicking my ass lol. When docked it works perfectly zero issues but...… when in handheld mode ZERO on screen, i swapped out the board into a known good one and still zero. any ideas?

Alfixes · Mar 4, 2021

Hi, I have same issue on one of my fixes. Haven't found solution yet but narrowing down to either components around screen connector area (diode or lcd bga 8316) i dont have time atm but will eventually get to it and will let you know if find solution.

KCVW · Mar 29, 2021

Can someone ID this diode please. (i've got a short on it)
It's next to the LCD connector.
The BGA IC in that circuit is a BD8316GWL according to a previous post.
Is it always the same on different hardware revisions of the board ??
My problem is that my switch works in docked mode but not in handheld mode.
Backlight and sound is ok, but no picture.
Obviously on a different board and not the one in the picure.

Pintglass · Mar 29, 2021

KCVW said:
Can someone ID this diode please. (i've got a short on it)
It's next to the LCD connector.
The BGA IC in that circuit is a BD8316GWL according to a previous post.
Is it always the same on different hardware revisions of the board ??
My problem is that my switch works in docked mode but not in handheld mode.
Backlight and sound is ok, but no picture.
Obviously on a different board and not the one in the picure.

Maybe RSX101VA-30 or equivalent

emuboarding · Apr 20, 2021

please... in Nintendo Switch Lite motherboard...
what is the value of this capacitor in this photos.

on the left side of the FT9CJ chip

jkyoho · Apr 20, 2021

emuboarding said:
please... in Nintendo Switch Lite motherboard...
what is the value of this capacitor in this photos.

on the left side of the FT9CJ chip

20nF On standard NS sub-board

NVM, I thought was the cap above

Titmando · Apr 25, 2021

Can I get help identifying these parts please as I require replacements for my Nintendo switch lite.

I need replacement parts: (Ignore the 8kohms box that was something I was diagnosing over on TronicFixs with a guy called Severance he pointed me to this forum.

Diode by the inductor coil underneath the BQ and M92 ic's
Replacement inductor coil
FPC connectors for the backlight, LCD, daughter board.
Power connector and various other components that are marked red in the thumbnails, new to the forums so I hope you can see the red boxes.

I just need replacement parts and ideas on where to buy them from thanks

Thanks in advanced for any help.

Kind Regards

Mike

golu18 · Apr 27, 2021

Hi everyone, I need some help trying to identify this part circled in the pic for my nintendo. I blew it away during the replacement of the ribbon connector at the back of the board and now I can't find it... Only thing I can read on it is ZBL 628 but no luck so far searching on the internet. So you guys are my last hope. Many thanks in advance!

note9 · Apr 27, 2021

RedViking said:
I'm working on fixing my switch (managed to knock loose a part and can't find it). The port is circled, Without it my fan runs wide open anytime the screen is on. Does anyone know what it is?View attachment 247350

also looking for the part. trying to repair a switch with a no spinning fan and that component was soldered opposite way.

note9 · May 8, 2021

update on the post above:

Mosfet near the fan connector. i've seen 3 different marking codes.

Marking code S D / not yet found

Marking code RY / ROHM RV2C002U
https://www.mouser.co.uk/ProductDetail/755-RV2C002UNT2L

Marking code SA / Nexperia PMZ600UNE
https://www.mouser.co.uk/ProductDetail/771-PMZ600UNEZ

note9 · May 12, 2021

anyone have values for the following components.

Hardware Components used on the Switch (mostly the motherboard and main console)

Well-Known Member

Member

Attachments

New Member

Attachments

Well-Known Member

New Member

New Member

New Member

New Member

Attachments

Member

Member

Member

New Member

Attachments

Well-Known Member

Active Member

Well-Known Member

New Member

New Member

Member

Member

Member

Similar threads

Popular threads in this forum