Hacking Black Screen on 8.0.1

skydancer93 · Apr 26, 2019

Updated Switch to 8.0.1 through the prompt as I read it was safe and now I get a black screen after booting to the Nintendo logo. Also, it seems harder to get into RCM. When I do, I get the Sept logo, then the Atmosphere logo and after the Nintendo logo, it shuts off. What's going on here.

Paulsar99 · Apr 26, 2019

Use the most latest atmosphere or kosmos cfw. Only the latest can support >8.0.0, lower than that and you will get the black screen.

skydancer93 · Apr 26, 2019

I am. I’m using 0.8.8. It was working before when I was on 8.0.0. But it asked me if I was ready start System update and reading that it was compatible, I did. Every since then, that sequence happens even after I reinstalled Atmosphere.

Paulsar99 · Apr 26, 2019

Weird. Maybe delete every traces of your old atmos and put a latest fresh atmos or kosmos, sometimes atmos can have issues if you copy paste the new files to the older ones.

skydancer93 · Apr 26, 2019

You don’t think something got broken do you?

stitchxd · Apr 26, 2019

skydancer93 said:
Updated Switch to 8.0.1 through the prompt as I read it was safe and now I get a black screen after booting to the Nintendo logo. Also, it seems harder to get into RCM. When I do, I get the Sept logo, then the Atmosphere logo and after the Nintendo logo, it shuts off. What's going on here.

Is your SDCARD exfat by chance? I had this issue with exfat.

zakenz · Apr 26, 2019

had the same issue installing 7.0.1 with choixdujour. Problem was my SD card was in exFAT and not FAT32. I fixed it by formatting my SD card in FAT32

Paulsar99 · Apr 26, 2019

If you're talking about rcm nah nintendo can't really do anything about that since it's a hardware flaw. When it comes to 8.0.0 cfw if you get blackscreen it usually about compatibility issues or sd card problems. But yeah like people said here if you have a spare sd card lying around you can format it to fat32 and try if it works on your switch.

skydancer93 · Apr 26, 2019

It is EXFAT yes. But that shouldn’t make it harder to RCM, no?

zakenz · Apr 26, 2019

skydancer93 said:
It is EXFAT yes. But that shouldn’t make it harder to RCM, no?

from my experience it does not

stitchxd · Apr 26, 2019

skydancer93 said:
It is EXFAT yes. But that shouldn’t make it harder to RCM, no?

If your RCM jig is bad that will be the cause (I went through two RCM jigs before finding one that was just the right size.)

That said, exfat is TERRRIBLE on the switch, it only has one partition table, so if something gets corrupt the switch can't recover from it. FAT32 however (though with it's own limitations that you will likely never run into because it has better support) uses two partition tables to avoid that.

skydancer93 · Apr 26, 2019

So I can just backup my SD card, format to FAT32 and put everything back on and everything will be fine?

stitchxd · Apr 26, 2019

skydancer93 said:
So I can just backup my SD card, format to FAT32 and put everything back on and everything will be fine?

yep! It will take time, when I had to convert mine (256GB) it took 3 hours from start to finish. and it was just over half full.

neav · Apr 26, 2019

Don't get confused with RCM and booting. When you can see all those cfw logo, it means your switch does enter RCM before. You can only push the payload if your switch is in RCM mode. If RCM failed it straight away boot to ofw or stay black screen without any splash screen if you install auto rcm before.

Your problem is booting the cfw, and this is more of the sd card problem (it's format, traces of old files etc..). Try what has already been suggested, use FAT32 sd card, and delete all old files and put in fresh atmos files.

Hacking Black Screen on 8.0.1

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Similar threads

Popular threads in this forum