Very doubtful encrypted.Thanks Matty.
I do have JLink and the ns-atmosphere, is there an instruction I can follow to get the dump for you ?
Have they encrypted it?
Very doubtful encrypted.
Just need to connect to SWDIO & SWDCLK and dump 0 - 8192, or ideally 0 - 262144.
BOSSA should be able to do it. Maybe.
mattytrog, I have SX Pro. I am going to do the Trinkey M0 when it arrives. Is there anything special I need to do to use the payload? It says it is for non-Pro users.
There is not a "launcher.bin" in the SXOS 2.5.3 download, only a boot.bin. Is that what you mean?Hi matty there are some reports that they can't inject any payload with tegrarcm/nxloader/dongle by entering to rcm and keeping the usb connected.
As I remember I was able to inject a payload with tegrarcm via PC... But I can't test it now.
Just add the launcher.bin from SXOS renamed to payload.bin in your sd (boot.dat too of course).
There is not a "launcher.bin" in the SXOS 2.5.3 download, only a boot.bin. Is that what you mean?
Hi, i'm use a Trinket M0 with the old Method1 4-wire setup and AutoRCM.
After all the time i want to update the modchip, which simple UF2 file should I use?
Hi matty there are some reports that they can't inject any payload with tegrarcm/nxloader/dongle by entering to rcm and keeping the usb connected.
As I remember I was able to inject a payload with tegrarcm via PC... But I can't test it now.
Just add the launcher.bin from SXOS renamed to payload.bin in your sd (boot.dat too of course).
You all good? If you get any problems let me know.@mattytrog
Haven’t updated my uf2 in a long time and things have changed since my install. I don’t plan on redoing my install and noticed you don’t state which uf2 file to use with the strapless(4-wire). So, which one?
I figured it out.
Have you put Simple-UF2 on there too?Mattytrog,
I got the Trinket M0. I did as the instructions say and got into Switchboot mode and installed the SWITCHBOOT_TRINKET_JOYCON_VOLUME.uf2software. I installed the chip into the Switch according to the Top Trinket M0 diagram using both straps but none of the Pink arrow add ons except the usb disconnect one. So, the chip goes into RCM mode as verified by TegraRcmSmash1213. i sent it a payload but got no results. I can see the red leds on the modchip flashing red but the Switch does not boot at all. I put the SX os payload .bin on the SD card. Any pointers on what to explore next? Thanks.
No thats the right one.SWITCHBOOT, then Simple-UF2.I have not put simple-UF2 on the card. I will try that. meanwhile I am going to re-do the wiring with a 40 AWG instead of 30 AWG.
kynar. thanks.
edit: I put TRINKET_REBUG_SIMPLE_UF2_V098r3 on the chip. can't find anything in the github called "simple-UF2.uf2". let me know which is the correct one and if there is really one named simple-uf2.where is it?
No thats the right one.SWITCHBOOT, then Simple-UF2.
It has to work. If it doesn`t you have a wire / soldering issue.
Been a bit busy. Release will come later todayHey Matty, when will you release the next version of UF2?
OK... 0.9.8r4 coming.
Someone do us a favour...
Download this and launch it.
See if anyone likes the look of it compared to standard Hekate.
Anyone like? Differences subtle...
Launch with TegraRCMsmash or rename to payload.bin or whatever. Only a test!
OK... 0.9.8r4 coming.
Someone do us a favour...
Download this and launch it.
See if anyone likes the look of it compared to standard Hekate.
Anyone like? Differences subtle...
Launch with TegraRCMsmash or rename to payload.bin or whatever. Only a test!