Very doubtful encrypted.
Just need to connect to SWDIO & SWDCLK and dump 0 - 8192, or ideally 0 - 262144.
BOSSA should be able to do it. Maybe.
Hi matty there are some reports that they can't inject any payload with tegrarcm/nxloader/dongle by entering to rcm and keeping the usb connected.
As I remember I was able to inject a payload with tegrarcm via PC... But I can't test it now.
Just add the launcher.bin from SXOS renamed to payload.bin in your sd (boot.dat too of course).
As I remember I was able to inject a payload with tegrarcm via PC... But I can't test it now.
Just add the launcher.bin from SXOS renamed to payload.bin in your sd (boot.dat too of course).
@mattytrog
Haven’t updated my uf2 in a long time and things have changed since my install. I don’t plan on redoing my install and noticed you don’t state which uf2 file to use with the strapless(4-wire). So, which one?
I figured it out.
Haven’t updated my uf2 in a long time and things have changed since my install. I don’t plan on redoing my install and noticed you don’t state which uf2 file to use with the strapless(4-wire). So, which one?
I figured it out.
Last edited by kylum,
Sorry I didn`t get alerts that anyone had posted in here 
Use TRINKET/REBUG.That will sort you out. Payload.bin can be ANY payload (for example sx loader 1.0)
Interesting...
There should be zero issues connecting to PC. If there are issues, it has to be poor soldering. More than likely a poor GND connection. I`d like to hear more about this
--------------------- MERGED ---------------------------
Use TRINKET/REBUG.That will sort you out. Payload.bin can be ANY payload (for example sx loader 1.0)
Interesting...
There should be zero issues connecting to PC. If there are issues, it has to be poor soldering. More than likely a poor GND connection. I`d like to hear more about this
--------------------- MERGED ---------------------------
You all good? If you get any problems let me know.
Mattytrog,
I got the Trinket M0. I did as the instructions say and got into Switchboot mode and installed the SWITCHBOOT_TRINKET_JOYCON_VOLUME.uf2software. I installed the chip into the Switch according to the Top Trinket M0 diagram using both straps but none of the Pink arrow add ons except the usb disconnect one. So, the chip goes into RCM mode as verified by TegraRcmSmash1213. i sent it a payload but got no results. I can see the red leds on the modchip flashing red but the Switch does not boot at all. I put the SX os payload .bin on the SD card. Any pointers on what to explore next? Thanks.
I got the Trinket M0. I did as the instructions say and got into Switchboot mode and installed the SWITCHBOOT_TRINKET_JOYCON_VOLUME.uf2software. I installed the chip into the Switch according to the Top Trinket M0 diagram using both straps but none of the Pink arrow add ons except the usb disconnect one. So, the chip goes into RCM mode as verified by TegraRcmSmash1213. i sent it a payload but got no results. I can see the red leds on the modchip flashing red but the Switch does not boot at all. I put the SX os payload .bin on the SD card. Any pointers on what to explore next? Thanks.
Last edited by jimh54,
I have not put simple-UF2 on the card. I will try that. meanwhile I am going to re-do the wiring with a 40 AWG instead of 30 AWG.
kynar. thanks.
edit: I put TRINKET_REBUG_SIMPLE_UF2_V098r3 on the chip. can't find anything in the github called "simple-UF2.uf2". let me know which is the correct one and if there is really one named simple-uf2.where is it?
Also, could you give an explanation of the led behaviors when it is correct? now I get a green led in the middle, and a slow flashing red on the edge led. when I open the chip in file explorer the files I installed disappeared. Is that ok?
kynar. thanks.
edit: I put TRINKET_REBUG_SIMPLE_UF2_V098r3 on the chip. can't find anything in the github called "simple-UF2.uf2". let me know which is the correct one and if there is really one named simple-uf2.where is it?
Also, could you give an explanation of the led behaviors when it is correct? now I get a green led in the middle, and a slow flashing red on the edge led. when I open the chip in file explorer the files I installed disappeared. Is that ok?
Last edited by jimh54,
No thats the right one.SWITCHBOOT, then Simple-UF2.
It has to work. If it doesn`t you have a wire / soldering issue.
OK... 0.9.8r4 coming.
Someone do us a favour...
Download this and launch it.
See if anyone likes the look of it compared to standard Hekate.
Anyone like? Differences subtle...
Launch with TegraRCMsmash or rename to payload.bin or whatever. Only a test!
Someone do us a favour...
Download this and launch it.
See if anyone likes the look of it compared to standard Hekate.
Anyone like? Differences subtle...
Launch with TegraRCMsmash or rename to payload.bin or whatever. Only a test!
D
Deleted User
Guest
Similar threads
-
K3Nv2
-
Psionic Roshambo
-
Xdqwerty
what are you looking at? - S salazarcosplay
-
-
-
-
-
-
S @ salazarcosplay:@SylverReZ youtube to mp3 some are still good, usefull when the official music video has better audio than the music in th ecd+1
-
-
-
-
-
@
Psionic Roshambo:
I used to have a few of those with Direct Sound on XP and Audigy Platinum sound card with high end speakers was a glorious time for audio
-
-
@
K3Nv2:
Some websites have full studio rips of production kind of hard to find for obvious reasons+1
-
@
Psionic Roshambo:
Not sure current audio codec based sound built in to motherboards can handle the bit depth those used
-
-
-
-
@
Psionic Roshambo:
Xdqwerty for most people hearing anything better than 256Kbps MP3 they cannot tell the difference
-
-
-
-
-
-
-
