Tutorial  Updated

Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

Notice: I am not receiving notifications for this thread. I didn`t realise people were still posting in it.

Please please accept my apologies if I haven`t replied to tags etc... I have no idea what is happening. I`m subscribed to this thread but I am not receiving notifications. Please inbox me if possible. Or tag me in another thread.

Its amazing that people are still checking all of this out. I thank you for all of the help and support I have received in this thread over this year.

Cheers. Matty.


A video showing a modchip in action. Thank you once again to @metaljay for providing this. This is what you can achieve by fitting a chip!



Section 1. Gather your software.

Get your chip software from THIS THREAD.
Follow the flashing instructions there...




Section 2. Removing USB port and unneeded LEDs. (Adafruit chips only)
  • Next, we need to remove the USB port from the modchip. I recommend a heatgun or a rework station. Heat up until the USB port just lifts off the modchip.
  • Do the same for the LED just to the right of the USB port.
See picture:
20181031_110415.jpg


You are now ready to fit your device. Proceed to Fitting section.





Section 3. Fitting modchip to your Switch.
New Universal Method. All SAMD-based internal chips. If your chip is not supported and you cannot work it out, PM me.

Trinket M0.
Solder as laid out in the following picture

trinketfinal.jpg

==================================================
Rebug SwitchME M0. Use Trinket files.
Solder as laid out in the following picture

rebugfinal.jpg

==================================================
RCMX86 - Internal modchip version.
Solder as laid out in the following picture

RCMX86-Internal-Final.jpg


==================================================
Gemma M0. Use Gemma files.
Solder as laid out in the following picture


gemma final.jpg

==================================================
ItsyBitsy M0 Express. Use ItsyBitsy files.
Solder as laid out in the following picture

itsybitsyfinal.jpg




==================================================
Feather M0 Express. Use Feather files.
Solder as laid out in the following picture

feather_final.jpg




BUILD YOUR OWN FROM A QFP ATSAMD21E18. Trinket equivalent pins.
Flash Trinket bootloader using OpenOCD via serial pins SWDIO / SWDCLK. Fit a reset switch somewhere... Or going to power / wake (aka method 2). If building for external use, it is good practice to fit a third capacitor between 3V & GND. This is deliberately vague and ambigious, as this needs research and you need to know what you are doing.

Link for setting the Pi up with OpenOCD: HERE
Raspberry Pi OpenOCD image in downloads section or HERE
SAMD pi connection.png



Alternative Solder Points

Credit to @consolex for original pic. I`ve added alternative points to solder to:
Alternatepoints.jpg


Credit to @pyorin for this much tidier version showing the same info as the above one!
Alternatepoints2.jpg

s-l1600.jpg

alternative3v.jpg




Replacement Parts List

Ok... So you have damaged your switch soldering your chip in. Not to worry.

First things first, DO NOT BRIDGE THE CONTACTS HOPING TO REVIVE YOUR SWITCH. With resistors, you may possibly get away with this, but with the capacitors listed below, if you jump these points, you will make a nice short-circuit to the PMIC and / or the M92T36, killing them instantly. Don`t do it.

OK... I`ll list these parts with METHOD 2 & 3 TRINKET PIN NUMBERS and the values of the components they solder to.

TRINKET 3V (POWER SUPPLY) - 2.2uF 0402 size MLCC capacitor. Voltage unimportant as long as it is over 6.3v
TRINKET PIN 2 (POWER ON RESET - goes to pin 5 on M92T36)- 4.7uF 0402 size MLCC capacitor. Voltage unimportant as long as it is over 6.3v
TRINKET PIN 0 (VOL+) - 150R (150 ohms) 0201 Thick Film resistor. 50mW
TRINKET RESET (SWITCH POWER BUTTON) - 150R (150 ohms) 0201 Thick Film resistor. 50mW


I recommend RS components.

FAQ

Q - How do I boot the switch into APX (RCM) mode?

A - You need to short out pin 10 on the right joycon rail to GND with a jig or modded joycon or paperclip (not recommended... Buy a jig you cheap-ass gyppo). Once shorted out, hold down vol+ and power. The switch screen should be off... Plug into your PC and it should recognise a APX device. Well done. You are in RCM.

Q - What glue should I use?
A - Only glue if necessary! Ideally if your soldering is of sufficient quality and your wire is thin enough, you don`t need glue. I use a bit because I am OCD. Anyway, use Epoxy. It`s what I use. Gives you some working time, is solid. Superglue makes a mess DO NOT USE SUPERGLUE. The only thing super about it is how it melts things. Epoxy won`t stick to the shield long-term, so bear that in mind. Pure Acetone will remove epoxy. Acetone tends to remove / melt anything to be warned. CHECK YOUR GLUE WON`T GO CONDUCTIVE OVER TIME - LOOKING AT YOU SCAMSUNG! The combination of heat cycles and absorbing of moisture can turn adhesive into a high-impedance connection!

Q - What size wire should I use?
A - I use AWG40 magnet wire or AWG30 Kynar. AWG40 goes onto components easier... And if you snap it, chances are the wire will snap and not the trace / component.
A2 - You can also use AWG30. I recommend Kynar wrapping wire but any will do. Looks nice, good resistance to elements, tidy. Nothing thicker than AWG30. You are just causing yourself more headaches. Trust me.

Q - Is AWG40 thick enough?
A - Yes. AWG40 is good for around 90mA.

Q - which methods do you recommend?
A - Connect all the straps...

Q - how do you recommend to set it up?
A - Fusee Suite. Search for Fusee Suite or go to link at top of this OP.

Q - My switch is flat and won't turn on.
A - Have you got the charger connected? Disconnect it or your switch won't boot! Boot to a payload (SX loader/Hekate), reconnect charger and leave on the payload menu and charge. Leave for 15 minutes and switch will start normally. It will continue charging one booted.

Disclaimer:
You have only yourself to blame. This voids warranty. This may or may not get you banned from online services. If it does, you got yourself banned. I`m not responsible if you kill your switch / your first-born with any of this in this post. I`m not infalliable. I`m partly senile. Do your own research. Kids, get bill payers permission before you attempt even using a screwdriver.
NUTSHELL: Don`t come having a go at me because you fooked your £300 console up. I`ll do my best to help you though if you do, Just don`t blame me.

Credits to Quantum-Cross, Atlas44, @Ninoh-FOX , @jcrorxp , @tecfreak, @mooglazer, @subcon959, @64Dp128k, @mikeleuskaldunak, @M-O-B, CTCaer, @evilsperm, @consolex and everyone else for valuable input.


IF YOU REQUIRE SUPPORT, IF YOUR CONSOLE ISN`T WORKING CORRECTLY... PLEASE POST A HIGH RESOLUTION PICTURE OF YOUR INSTALL. You might think it isn`t your soldering, but in all cases with the new methods, it is bad soldering. So, please post a picture.


A BRIEF WARNING - PLEASE READ
THIS MOD IS NOT FOR THE FEINT OF HEART. WE ARE SOLDERING TO TRACES AND COMPONENTS ON THE FRONT SIDE OF THE BOARD TO SAVE HAVING TO REMOVE THE BOARD AND SOLDER TO TESTPOINTS. IF YOU ARE STRUGGLING, OR THINK YOU ARE GOING TO STRUGGLE, PLEASE PLEASE SOLDER TO THE TEST POINTS NOTED IN THIS AND OTHER THREADS (YOU WILL NEED TO REMOVE THE MOTHERBOARD). DOUBLE - TRIPLE CHECK EVERYTHING. YOU HAVE BEEN WARNED!!!
Good soldering skills are needed!
A magnifying glass is needed!
Good soldering iron needed - ideally with a 0.3 conical tip. No more than 30w!
SECURE YOUR WIRES PRIOR TO SOLDERING. Stick them down with double-sided tape.
Only use glue if you need to and glue wires after soldering. Don`t glue the solder to the component!
Put the tiniest amount of glue on the PCB mask only. Never on components. Use a cocktail stick for more glue control!!!
Take a look at alternative solder points to get you out of the sh*t if you do rip something off the board
If you aren`t the best at soldering, then think very carefully about connecting to pin 6 capacitor (the one in these new methods). If you rip this pad, you WILL NEED TO REMOVE YOUR BOARD and run from a testpoint.
 

Attachments

  • Trinket equivalent.png
    Trinket equivalent.png
    118 KB · Views: 3,784
Last edited by mattytrog,

chronoss

Well-Known Member
Member
Joined
May 26, 2015
Messages
3,005
Trophies
1
XP
4,828
Country
Congo, Republic of the
Damaged the resistor? You can bridge it.
:hrth::hrth::hrth::hrth::hrth::hrth::hrth::hrth::hrth:
yaaaaaa it work now and i have the same screen in op :)

I want to boot directly into cfw without press volume, how i can do ?

If you want to permanently boot into CFW, you need Version 2. OFW boot is still possible if you hold reset on your modchip while powering on. Do not hold any buttons apart from RESET on your modchip. You then power on. Let go after a second or so. Your console should boot into OFW.

I tested all file in the pack, i must always press Power + Volume+ to boot on the trinket :(
 
Last edited by chronoss,

mattytrog

You don`t want to listen to anything I say.
OP
Member
Joined
Apr 27, 2018
Messages
3,708
Trophies
0
Age
48
XP
4,328
Country
United Kingdom
:hrth::hrth::hrth::hrth::hrth::hrth::hrth::hrth::hrth:
yaaaaaa it work now and i have the same screen in op :)

I want to boot directly into cfw without press volume, how i can do ?



I tested all file in the pack, i must always press Power + Volume+ to boot on the trinket :(
You need to make sure both straps are correctly fitted and use version 2
 
  • Like
Reactions: chronoss

ZZ007

Member
Newcomer
Joined
Nov 28, 2016
Messages
5
Trophies
0
Age
48
XP
85
Country
France
I want dual boot .
Official firmware by default & Sx Os with "Vol+ & Power"

Wich is the best method ?
And files to trinket?
 

mattytrog

You don`t want to listen to anything I say.
OP
Member
Joined
Apr 27, 2018
Messages
3,708
Trophies
0
Age
48
XP
4,328
Country
United Kingdom
What do you mean by "both straps are correctly fitted" ??????
The joycon and vol+ strap. You need those fitted to have fully automated CFW boot without autoRCM.

--------------------- MERGED ---------------------------

ItsyBitsy M0 Express not working,please guide or uf2 correct thanks
Just tested. Working fine?

Needs updating to Hekate 4.5 though. But it works perfectly.

Updated OP with fresh download links.
 
Last edited by mattytrog,
  • Like
Reactions: psp95

psp95

Member
Newcomer
Joined
Dec 6, 2018
Messages
12
Trophies
0
Age
34
XP
84
Country
Italy
The joycon and vol+ strap. You need those fitted to have fully automated CFW boot without autoRCM.

--------------------- MERGED ---------------------------


Just tested. Working fine?

Needs updating to Hekate 4.5 though. But it works perfectly.

Updated OP with fresh download links.

I installed all wires, except vol +, first install joycon only bootloder and then I put either mode1 or mode2 (nx file) but it does not go :(

--------------------- MERGED ---------------------------

I can not flash the bootloader (uf2) via usb type c switch, only with chip connector, we always talk about the
itsybitsy
 

mattytrog

You don`t want to listen to anything I say.
OP
Member
Joined
Apr 27, 2018
Messages
3,708
Trophies
0
Age
48
XP
4,328
Country
United Kingdom
I installed all wires, except vol +, first install joycon only bootloder and then I put either mode1 or mode2 (nx file) but it does not go :(

--------------------- MERGED ---------------------------

I can not flash the bootloader (uf2) via usb type c switch, only with chip connector, we always talk about the
itsybitsy
Are you following the correct procedure for updating the chip?

Disconnect from USB
Double press reset until light is breathing
Connect to USB
Flash uf2.
 

MrDDON

Member
Newcomer
Joined
Jun 19, 2018
Messages
9
Trophies
0
Age
32
XP
168
Country
Germany
Hey guys!

First Post, not first time around here.

I just tried this awesome tutroial the last 2 hours: it worked! #wohoo

Had a few issues with the common 3V point, switched that to the one at the eMMC, it worked!

So thank you for that awesome stuff u all make in this nice forum and keep on going <3
 
  • Like
Reactions: mattytrog

mattytrog

You don`t want to listen to anything I say.
OP
Member
Joined
Apr 27, 2018
Messages
3,708
Trophies
0
Age
48
XP
4,328
Country
United Kingdom
Hey guys!

First Post, not first time around here.

I just tried this awesome tutroial the last 2 hours: it worked! #wohoo

Had a few issues with the common 3V point, switched that to the one at the eMMC, it worked!

So thank you for that awesome stuff u all make in this nice forum and keep on going <3
Thank you for the feedback kind sir!
 
  • Like
Reactions: MrDDON

mattytrog

You don`t want to listen to anything I say.
OP
Member
Joined
Apr 27, 2018
Messages
3,708
Trophies
0
Age
48
XP
4,328
Country
United Kingdom
OK... Bit of an update being pushed either tonight or tomorrow.

For single payload users...

No 0 folder required...

UF2 will either boot "payload.bin" or "start.bin" by default. Can be any payload. Will look on root of SD

If they don`t exist, Hekate will boot. No folders or anything will be made.

Nothing else required.

Any good to anybody?
 
Last edited by mattytrog,
  • Like
Reactions: MrDDON

Site & Scene News

Popular threads in this forum

General chit-chat
Help Users
  • No one is chatting at the moment.
    K3Nv2 @ K3Nv2: Sorry for accidentally bending over