Homebrew PROBLEM AFTER HARDMOD DONGRADE.PLESE HELP!!!!(NEW 3DS XL)

geopis · Feb 6, 2016

Hi everyone.As a new member i enjoy you geat community!!!!
Ι have the following problem :
After a succesful downgrade 10.4 to 9.2 the coslole was in complete working order . After that , i have decided to removed the 4 cables CLK ,DATA0 SMD and GROUND because for me they are not usefull now in 9.2fw .
After console assembly i try to power on and i see the blue bottom screen as before in hardmod work.
i have disassebly the console and i found clk and the upper solder pad are missing . This is cause the problem for that mallfuction ?
Please can you help me and tell me what is wrong?
Can i fix it ?
If solder a cable (bridge) just like in the photo solve my problem?

i have already uploaded 2 photos of my problem to be more clear .

Thank you in advance for you hospitality and help who i found in your site
Best regards,George!

izy · Feb 6, 2016

well i cant see you photos maybe upload them and post the links to them lol imgur is a good image host

but fixing the solder points should hopefully fix your problem since you are not getting a working circuit which is causing an error from the sounds of it

geopis · Feb 6, 2016

squee666 said:
well i cant see you photos maybe upload them and post the links to them lol imgur is a good image host

but fixing the solder points should hopefully fix your problem since you are not getting a working circuit which is causing an error from the sounds of it

The images are ready.
If solder a bridge you think solve my problem?

Thank you for your quick response!

izy · Feb 6, 2016

geopis said:
The images are ready.
If solder a bridge you think solve my problem?

Thank you for your quick response!

well if the 2 are linked then soldering a bridge should hopefully fix your issue, if not something else may have been damaged on hardmod removal

geopis · Feb 6, 2016

Finnly i found the solution.
I make the bridge and my problem solded :grog:

here is the proof

renelima · Apr 23, 2016

I was making a hard mode to back up my nand. I welds the DATA0, CMD, GND and tried to weld the CLK, however saw not give account to solder the CLK, removed the welds and rode the new 3ds, when I call did not work anymore and appeared BSOD.

00F800FE
00000000
00000000
00000400
00000000

I dismounted and saw that the four CLK solder points were torn when I was trying to solder it. What I do there is a way to change the circuit, make a bridge to another spot on the board?
I think it's a hardware problem because not tried to get back up, only did the welds did not even call anything on my computer.

Someone help me!!!!

milerwan · Apr 24, 2016

You have to do the same bridge like geopis.

75mak · Jun 26, 2016

is this bridge required if the hardmod wires are desoldered/removed?

Is there any set procedure in removing the wires for hardmod once you have downgraded to 9.2 - so as to avoid doing this bridge?

VashTS · Jun 26, 2016

id personally just snip the wire from the connector and tape the ends so it doesnt short anything out.

i wouldn't try to de-solder but if i did, id use a desolder braid and VERY carefully and slowly remove the wiring.

I think i might remove my hard mod, the spot i choose bulges slightly (under the back cover, near the battery on o3ds XL).

then if i ever need to hard mod i can simply splice a new connector in and we should be good to go.

75mak · Jun 26, 2016

VashTS said:
id personally just snip the wire from the connector and tape the ends so it doesnt short anything out.

i wouldn't try to de-solder but if i did, id use a desolder braid and VERY carefully and slowly remove the wiring.

I think i might remove my hard mod, the spot i choose bulges slightly (under the back cover, near the battery on o3ds XL).

then if i ever need to hard mod i can simply splice a new connector in and we should be good to go.

I'm planning on doing a few consoles. So I want to reuse the sd card reader. Just wondering how I can safely remove the ends... is there any reason why you wouldn't desolder... does it cause problems?

VashTS · Jun 26, 2016

75mak said:
I'm planning on doing a few consoles. So I want to reuse the sd card reader. Just wondering how I can safely remove the ends... is there any reason why you wouldn't desolder... does it cause problems?

Too much of a risk that is not needed.

ollicnat · Sep 17, 2016

The geopis method works thanks so mucho , pura vida!

farpo · Sep 18, 2016

hello to everybody
I have the same problem
the clk pad is gone and I have blue screen also with hardmod unmonted
I done the dump nand and also rewrite the patched nand without any error (using an alternative clk pad on the other side of themobo).
My problem is that i have a different mobo compared to geopis
i attached a photo found on the forum
plz help me for a solution
thanks

urherenow · Sep 18, 2016

The 1 console I messed up, I tore off the bottom left joint. Never could get it fixed, and I tried bridging it with only solder. Isn't there a micro via under that one? It must be connecting to something somehow... The OP is extremely lucky to recover from that.

With that said... NEVER pull on a wire when desoldering, and NEVER use more heat than when you are soldering. The first step to desoldering is to ADD MORE SOLDER. A good joint does not melt easily with an iron, but nothing conducts heat better than liquid solder. As soon as you melt new solder onto the joint, the joint will melt and you can suck it up with a solder sucker or some braid. The wire will just come off naturally.

DrPhibez · Nov 13, 2016

geopis said:
Finnly i found the solution.
I make the bridge and my problem solded
here is the proof
View attachment 37836 View attachment 37837

What did you solder to on the right side?

xxadmxx · Dec 13, 2016

hello everyone, i am new member of this community, and i think people here can help me with my problem. i have an old 3ds xl, and i perform a hardmod recently, i follow the guide here and i successfully solder the 4 pins and after i plugged in the sd to my computer, now my 3ds wont turn on completely, the blue light ( power ) does not turning on, but when i plug in the charger, it charge normally, ( orange light comes up ) so my question is, is there any way of fixing this? please help.

Homebrew PROBLEM AFTER HARDMOD DONGRADE.PLESE HELP!!!!(NEW 3DS XL)

Member

Advanced Tech Pleb

Member

Advanced Tech Pleb

Member

Member

Seasoned technician

Well-Known Member

Beat it, son

Well-Known Member

Beat it, son

Active Member

New Member

Attachments

Well-Known Member

New Member

Member

Similar threads

Popular threads in this forum