Hacking [Tutorial] How to access NNID and eShop on 9.5.0-23 Emunand
- Thread starter Xenon Hacks
- Start date
- Views 124,322
- Replies 816
- Likes 22
Guessing you installed the updated eshop then.
You need to download the version of the eshop that matches your installed emunand version and install it, then use HANS to access the eshop.
You need to download the version of the eshop that matches your installed emunand version and install it, then use HANS to access the eshop.
First questions he shouldve asked were:
What steps are you following?
What is your setup?
Im following this tutorialHello GBATEMP this is a quick tutorial on how to access the eShop and sign into or manage your NNID settings, but first let's get a few checks before doing anything.
Requirements
The Gateway Red card (CFW users check the notes below)
A N3DS / N3DSXL / N3DSLL
An Emunand partition with firmware 9.X.X-XX U/E/J
Dev Menu as a 3DS or CIA (The 3DS version can be found on Gateways download section)
3DSNUS - Credits to @ground
emuNAND Tool - Credits to @n1ghty
Free multi patcher - Credits to @RednaxelaNnamtra
Tutorial
Ok with that out of the way lets begin.
Open 3DNUS as an administrator and download the NVER and TIGER for your region they are as follows
U
Title ID: 000400DB20016302
Version: 448
E
Title ID: 000400DB20016102
Version: 448
J
Title ID: 000400DB20016202
Version: 448U
Title ID: 0004001000021900
Version: 19465
E
Title ID: 0004001000022900
Version: 19465
J
Title ID: 0004001000020900
Version: 19465
Here is an example of what you would type into 3DNUS if I were trying to download the U NVER
Once you have both the NVER and TIGER CIA's inside of the 3DNUS 1.9 folder move them both to your SD card where you normally keep your CIA's
Before you install either of those CIA's Plug your MicroSD card into your PC using an adapter and open Emunand Tool then select Extract Emunand and save emuNAND.bin to your desktop this will be a backup incase the update fails and your Emunand bricks.
Once you have a backup simply boot into your Emunand. To confirm you are in Emunand open the rom selection menu and check the top right for Emunand if it says Sysnand do not continue as can possibly brick your N3DS.
From there open Dev Menu from either your Red card or as a CIA and install both CIA's. Once completed shutdown your N3DS and boot into Emunand did your brick? If you did simply inject your Emunand backup with emuNAND Tool and try again.
Spoofing the eShop and NNID Settings
When your Enter Emunand install Free multi patcher and run it.
Your setting in it should say
e-shop spoof - on
region patch - off
no auto download - on
then click A to save and start to apply those patches
From there simply enter the eShop like you normally would or go to your system settings and open Nintendo Network ID Settings to log into your NNID, set up a NNID, or change its settings.
Congratulations!
You did it! I hope this tutorial was easy to follow if there are any errors please point them out.
My setup is a 9.5 emunand rxtools n3DS, Eur.
Considering the thread it is a safe assumption he is following this tutorial and that he has a N3DS and is not using Reinand and 10.3. I did ask if he was using GW or CFW, which is the only other piece of info needed.
Then you installed the updated eshop. You need to download a N3DS 9.5.0-23E update package from that iso site, extract 00040100022900.cia from it and install that file. This will restore the proper eshop version. Then you can use HANS to access the ehsop.
In the future, please thoroughly read every part of a tutorial before doing the steps outlined. It is clearly stated that the bulk of this tutorial is only for GW users.
Running sysnand 9.2 / rxTools 9.5 on my N3DSXL. Installed both NVER and TIGER. Ran multipatcher with the listed settings. Now whenever I try to access eShop on my home menu it just gives me an endless loop with the nintendo 3ds screen logo
JFC people READ THE POST FULLY.
It says in BIG RED LETTERS that you should only install updated Tiger if you use Gateway, and that it will not work for CFW users.
You need to do what I told the previous user to do, only you want a 9.5.0-32U package and the title you want is 0004001000021900.cia
So how would I go about restoring my eshop to the previous version with the specified cia file? I tried using cia installer but it's telling me that it's invalid
Use DevMenu or sysupdater. Both should install it over the existing one.
If you want to use FBI you have to set the destination to NAND first, and probably delete the existing installed title because it is a higher version.
If you want to use FBI you have to set the destination to NAND first, and probably delete the existing installed title because it is a higher version.
And it's safe to just have that one cia file in the 'updates' folder? I can just run syspdater like that?
Similar threads
