Man hasn't posted in over a year, and then comes in with a slapping-good install. I will admit, powering on a switch at 9.4% does activate a deeper portion of my OCD, CHARGE THAT POOR THING!
Picofly AIO Thread
- Thread starter Adran_Marit
- Start date
- Views 513,670
- Replies 3,351
- Likes 60
Hey all I've made a google form to try and consolidate information on the blue/black screen issues people are having.
If you have had this issue, please fill out THIS form and if there is any information i didn't ask or didn't get fill in let me know.
Thanks
If you have had this issue, please fill out THIS form and if there is any information i didn't ask or didn't get fill in let me know.
Thanks
- Joined
- Sep 2, 2020
- Messages
- 1,267
- Trophies
- 0
- Age
- 39
- Location
- TORONTO
- Website
- form.jotform.com
- XP
- 2,198
- Country
Purple screen is normally from a different issue, image taken from switchbrew, my thing is to try and collect information on why we getting blue and black so much and what the common factors are
hello, can anyone help me, why does the light on my picofly just keep on turning blue? and no display
lampunya cuma biru, saya tunggu sekitar 3 menit tetap biru dan akhirnya lampunya mati
Post automatically merged:
lampunya cuma biru, saya tunggu sekitar 3 menit tetap biru dan akhirnya lampunya mati
Attachments
Last edited by aguskaryana,
@abal1000x had a theory about the defective dat0 adapter. In that case, more questions about removing dat0 adapter need to be asked.
I did a my first OLED today and I felt the same, however it isnt that bad. Have a multimeter in diode mode put positive lead on ground (apu shield or usbc con) and use negative lead to test DAT0 point. should be .5 - .9
One of the questions is which model switch so that elimates dat0 if it's anything other than oled
Hi guys!
So ... I tried to install the picofly into a switch lite, and the first time i plugged the battery, i noticed that the CPU is turning really hot. so i unplug it quickly
scared of the possibility of having a dead-fried switch, i unsolder 3.3v and gnd (i guess that this disabled the chip), and after that i got PURPLE SCREEN.
as far i've read the thread, it seems that a purple screen is fixable, but do i need the picofly working, right? (to boot hekate and read the eMMC and stuff)
i installed picofly on a erista v1 and all went fine. maybe the lite is having issues with picofly?
So ... I tried to install the picofly into a switch lite, and the first time i plugged the battery, i noticed that the CPU is turning really hot. so i unplug it quickly
scared of the possibility of having a dead-fried switch, i unsolder 3.3v and gnd (i guess that this disabled the chip), and after that i got PURPLE SCREEN.
as far i've read the thread, it seems that a purple screen is fixable, but do i need the picofly working, right? (to boot hekate and read the eMMC and stuff)
i installed picofly on a erista v1 and all went fine. maybe the lite is having issues with picofly?
What is this?, please use goog translate at the very least.
You can download official atmos from here, no need third party sources.
https://github.com/Atmosphere-NX/Atmosphere
Or go here for easier.
https://www.sdsetup.com/console?switch
Post automatically merged:
Check mosfet instalation and cpu flex, redo if necessary.
And no need for this jumper.
Post automatically merged:
Pictures?Hi guys!
So ... I tried to install the picofly into a switch lite, and the first time i plugged the battery, i noticed that the CPU is turning really hot. so i unplug it quickly
scared of the possibility of having a dead-fried switch, i unsolder 3.3v and gnd (i guess that this disabled the chip), and after that i got PURPLE SCREEN.
as far i've read the thread, it seems that a purple screen is fixable, but do i need the picofly working, right? (to boot hekate and read the eMMC and stuff)
i installed picofly on a erista v1 and all went fine. maybe the lite is having issues with picofly?
Last edited by cgtchy0412,
Try to detach CPU pin from pico, it should boot to OFW., or black screen ?
If it boots normal then buy another cpu flex or better do manual mosfet instalation.
can you help my problem?
Post automatically merged:
Saya melepas pin CPU, layarnya hitam, tidak bisa boot ofw
You must restore the ability to boot into OFW first.
1. Remove D0 from mainboard clean it with flux, use macro camera to confirm. Try ofw boot, if failed then
2. Remove cmd&clk from mainboard, clean it, try, if failed then
3. Remove rst.
4. Remove CPU flex.
5. Remove all.
Once you boot an OFW then redo the instalation with fresh cables, this time take it slow and precise. And before wiring it into Pico make sure that it can boot to ofw before.
For example, in this condition the unit should be able to boot into OFW.
1. Remove D0 from mainboard clean it with flux, use macro camera to confirm. Try ofw boot, if failed then
2. Remove cmd&clk from mainboard, clean it, try, if failed then
3. Remove rst.
4. Remove CPU flex.
5. Remove all.
Once you boot an OFW then redo the instalation with fresh cables, this time take it slow and precise. And before wiring it into Pico make sure that it can boot to ofw before.
For example, in this condition the unit should be able to boot into OFW.
I have removed picofl and all cables are back to normal but still won't boot, is there something wrong?
Check any damage on solder points? traces? components? shorts?
Oftenly black screen is caused by short, clean all again with flux and hope.
Death sentence should be corrupt emmc or dead cpu.
I just installed picofly, then I turned it on, it turned green and turned on, after that I turned it off again and I turned it on, it just turned on blue again and I booted without picoflay, it doesn't want it, but when Picofly wants to go green, the switch normally turns on, does it have to boot using picofly now?? I'm so confused
a video or picture would help.
And you dont need to have pico installed just to boot ofw.
Also be patient, and prepare now to order new flex cable and new rp board, if you still want to continue the mod.
If you cannot succeed with existing accs then buy a spare and test fresh.
For comparisson, i killed almost 5 pico boards, although it was normal pi pico, maybe at the trimming stage it broke some traces. But thats the price.
Hi,
I have rather interesting problem with Picofly. I installed it, NO SD screen is pretty fast but it is booting hekate really slow 30-40 seconds and it couldn't init SD Card. I can boot to OFW and it couldn't see SD Card either. I changed SD Card PCB with another no luck. There is no visible damage on SD Card connector and Mainboard connector.
BTW: OLED with SK Hynix EMMC and I tried different known good SD Card.
What can cause this? I can't partition the SD because it can't init.
Regards,
I have rather interesting problem with Picofly. I installed it, NO SD screen is pretty fast but it is booting hekate really slow 30-40 seconds and it couldn't init SD Card. I can boot to OFW and it couldn't see SD Card either. I changed SD Card PCB with another no luck. There is no visible damage on SD Card connector and Mainboard connector.
BTW: OLED with SK Hynix EMMC and I tried different known good SD Card.
What can cause this? I can't partition the SD because it can't init.
Regards,
Similar threads
- No one is chatting at the moment.
-
@ HiradeGirl:
Any TV with your PC connected with Citra and any smartphone to use as a screen using a free play store app.+1 -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
@
NinStar:
quite ironic that brawlhalla has a far superior netcode compared to smash bros ultimate while offering free online play with crossplay support -
