https://www.aliexpress.com/item/1005005315891694.html
I purchased this type of 4-anchor adapter.
What you actually receive is the 3-anchor piece of garbage in the attached picture.
I have bought one from multiple sellers and they were all the same.
I purchased this type of 4-anchor adapter.
What you actually receive is the 3-anchor piece of garbage in the attached picture.
I have bought one from multiple sellers and they were all the same.
Attachments
Last edited by ppeach,
I think at this point the best solution is https://munia.io/devices
It does not have any anchor points so you need to use UV mask or glue but at least you don't risk fu*king the emmc.
*Edit: they seem to lean to the right by default so I guess bridging the second pin does not matter after all.
That is 3 point.
Open the image from the review its 3 point.
And the 4 point doesn't have 2 test point, only 1 which is the Dat0.
Bought 4 10days ago from that shop and camed the 3-anchor with 3.3v
Careful
I made a mistake copying the link.
I ordered a dat0 adapter with 4 anchors.
Not the garbage that kills emmc with 3 anchors.
Post automatically merged:
hwfly official sells newer newer adapters than 4 anchor.
If you buy a dat0 adapter with a 4 anchor product image from most stores, you will probably receive 3 anchor garbage.
Ordered back in March from that store and got good ones. Ordered on 20th of May and got garbage.
Asked a refund and the seller won't give money back, waiting for the Ali to intervene.
Haven't tried them yet, but those are Frank's, and he knows well his stuff
I’ve just received rp2040-tiny, but when I’m trying to flash the firmware I can’t get the device “storage” to drag and drop the firmware. It flashes static red on the usb-c adapter.
I tried with and without boot button pressed.
Anyone has the same problem?
I tried with and without boot button pressed.
Anyone has the same problem?
So....i can leave the the unmarked ones without solder ball?
Post automatically merged:
I guess i can leave some points wihtout solder balls to pass jumper wire fron clk and cmd right?
Last edited by Flaviocarvalho,
I have a question. My Switch emmc is corrupted and I don't have a backup btw I have another switch backup and prod key. Can I use the other backup or nintendo will ban the switch because they both have same seriel number. Or should I go with a blank product key with zero seriel?
it works fine now but I was going to get crazy hahaha
yep, the unmarked ones aren't connected to anything on the switch motherboard. according to the emmc standard, they shouldn't be connected to anything in the emmc chip either. You need to keep some of the unused solder balls for the emmc to self-align properly when heating it though.
in theory it's possible to run jumper wires from clk and cmd, but I think it would be rather difficult to mount the emmc flat enough with multiple jumper wires in place.
It's possible to use the picofly_toolbox on IRAM? or that tool use more memory?
The question it's because i removed the usb c port with soldering iron and can't update by physical on rp2040.
*NOTE, THIS IT'S JUST MY CASE*
Another thing it's that using a rp2040 xiao version, the gliching process was very unestable, sometimes the "No Sdcard" screen boot in 2 seconds, but others just take 30-40 seconds.
When put an rp2040 aliexpress version, i got constancy 2 seconds or less on every "No Sdcard" screen, that's too curious.
Everything using V2 Flex on my lite.
Not able to boot other's payload that ums-loader until now.
The question it's because i removed the usb c port with soldering iron and can't update by physical on rp2040.
*NOTE, THIS IT'S JUST MY CASE*
Another thing it's that using a rp2040 xiao version, the gliching process was very unestable, sometimes the "No Sdcard" screen boot in 2 seconds, but others just take 30-40 seconds.
When put an rp2040 aliexpress version, i got constancy 2 seconds or less on every "No Sdcard" screen, that's too curious.
Everything using V2 Flex on my lite.
Not able to boot other's payload that ums-loader until now.
I got that error too and lost hope.
Correct me if I'm wrong: when fully installing a MOSFET, is it normal for D and S to show continuity ( if G was somehow triggered), but G should not to either?
Post automatically merged:
Hi @rehius. I've seen quite a few people complain about the *== error (dead CPU, poor wiring).
Some say it's CLK, CMD, and others think it's MOSFETs. Would you kindly clarify what wiring I should think of when I see this error? Thanks <3
Last edited by FreeLander,
I have same problem with my lite after install i get "no sd card" then when i insert sd card then black screen then when i boot to ofw using +&- button it's blue screen
xiao is bad.
even on my other project on uv sensor, it broke my smartphone power ic, when i use it as otg.
I have used seeeds studio product couple of time, and their design is bad, usually unstable. I also experience with their mtk.xxxx also unstable.
This is first time i use waveshare and impress with their design. its more stable.
Similar threads
-
-
-
@
Psionic Roshambo:
My phone is pretty secure the Chinese spies tell me it's really locked down and I probably should eat more fiber lol+2 -
-
-
-
-
-
-
-
@
BakerMan:
@SylverReZ I didn't say I watched either, did I?
I didn't actively watch them, rather, I had the misfortune of witnessing that shit -
-
tempBOT:
LeoTCK has joined the room. -
-
-
-
-
-
@
SylverReZ:
@K3Nv2, Ah shit, here we go again. I ain't represented Grove Street in five years, but the Ballas won't give a shit. -
-
-
-
-
-
Always touching 
] brb
