Nah the first install i did I had two mosfets outside of the cpu shield, the rest all glued inside the shield
When you install the mosfet outside the apu shield, and the glitch worked, did you use 30awg, around 10 cm length?
Post automatically merged:
(Sorry lot of ask, i might replicate this. Its wonderful if i could do it. I will change my default mod as mosfet outside from the apu.)
The gnd of the mosfet, you take it from the cap, the chasis or somewhere else?
I've used the CPU ground(the small square in the right hand corner of the cpu), but it it a hard connection to make, I just use the chasis now
I have updated to firmware 2.74 ，Picofly keeps waking up my device ，so I can't completely shut down. I'm not sure if this is a common situation. My device is a Switch OLED.
another attempt on 2nd OLED, damn my screen wont turn on but it got sounds
(this before instaling rp2040, one final test to OFW ), does anyone have any idea what to check ? 
, all connector seems fine
(this before instaling rp2040, one final test to OFW ), does anyone have any idea what to check ? , all connector seems fine
Last edited by blackheartme,
Once among us cleaned the flex using ipa.another attempt on 2nd OLED, damn my screen wont turn on but it got sounds
The device will wake if you plug a usb cable in fyi
Post automatically merged:
Check the pins inside the female flex connectoranother attempt on 2nd OLED, damn my screen wont turn on but it got sounds
No, I didn’t insert a USB. It’s just battery-powered. After I turn off the power, the chip will work and wake up the device.
The chip does not wake the console. This is a well known RTC auto power on after shutdown used by N system. Every Switch console automatically turns on after poweroff from the Horizon OS, even the unmodded ones.
The picofly firmware detects that and automatically shuts the system down after the successful glitch.
You can seperate them there is no harm, but you have to make sure good secure connection. Do not make cables too long or different sizes. Make it as short as possible and same size.
Sent from my iPhone using Tapatalk
So, using the yellow way in the picture is ok?
I tried to soldering using the green example but I can't do it very well.
Attachments
That squared is very difficult to solder. I am afraid you breaking something while doing it. Better just use chassis, simple and easy.
I personally don’t recommend using APU as ground point. Use APU shield instead.
Sent from my iPhone using Tapatalk
Solder like purple lines. Yellow is more difficult
Attachments
Ok, I`ll use shield as ground point. Thanks.
I can´t see any purple lines on the image I`ve attached. You mean same as Bad and Abal? Using APU shield as ground point?
BTW, Can I use APU shield too soldering the GND point of RP2040? In the past I modded one Lite and the ground point at the capacitor scares me a little bit hahaha
Yes you can use APU shield as ground point. You can also use TYPE-C connector on Lite console.
Sent from my iPhone using Tapatalk
Similar threads
-
Xdqwerty
what are you looking at?
-
-
-
-
-
-
-
-
-
-
-
@
Xdqwerty:
@realtimesave, hey there buddy chum pal friend buddy pal chum bud friend fella bruther amigo pal buddy friend chummy chum chum pal
-
@
Xdqwerty:
@realtimesave, hey there buddy chum pal friend buddy pal chum bud friend fella bruther amigo pal buddy friend chummy chum chum pal
-
-
-
-
-
-
-
-
-
-
-
@
Sicklyboy:
@Xdqwerty, Osu! Tatakae! Ouendan! is the Japanese version of the game, different settings/characters/songs but otherwise identical mechanics. I played that before I knew about Elite Beat Agents lol. Both fantastic games https://en.wikipedia.org/wiki/Osu!_Tatakae!_Ouendan+1 -
-
