Picofly AIO Thread
- Thread starter Adran_Marit
- Start date
- Views 510,927
- Replies 3,347
- Likes 60
Try launching OFW sysnand with hekate and see if it boots. If not, its probably the unlock that failed. I flashed 2.5 and unlock separately
I am able to reboot in original firmware without any problems... But i dont know how to launch Atmosphere... to launch atmosphere, don't you have to run the payload fuse.bin?
Post automatically merged:
Thanks my friend.. That solves my problem... I have to separately flash unlock and atmosphere runs without any problems.. Thanks a lot for all your Information... I am now here to help to anyone that have a problem!!!! I have instaled the picoflash in a nintendo switch v2.. If anyone have any problem.., i am here to help!
Last edited by papafria,
I'm sorry that's more of a cfw issue than a rp2040 issue from the sounds. I suggest asking in the noob thread
edit: ignore me, my page didnt load properly
Post automatically merged:
It might be the device ID issue that affects some of the zeros, but I have personally seen installs with the rp2040-one working
So you have the tools and skill to micro-solder everything but you can't determine what parts are needed from the first post?Is it possible that SOMEBODY PLEASE shares all necessary parts (as a SHOP-LINK) for this Project to avoid any mistakes?
I mean, I would like to mod my Switch Lite and my Switch OLED, but I dont have any idea, what flex-cables and other parts I need (besides the resistors and the RP2040 board)
At present there is no package you can purchase with all the pieces together.
Is it possible that SOMEBODY PLEASE shares all necessary parts (as a SHOP-LINK) for this Project to avoid any mistakes?
I mean, I would like to mod my Switch Lite and my Switch OLED, but I dont have any idea, what flex-cables and other parts I need (besides the resistors and the RP2040 board)
here a full step by step guide to install (into descrpition of the video you can find all equipment
)
A little question.
I used combined firmware from github but it didn't work so i had to run picofly_tb.bin from hekate (since i already removed the port).
I saw that unlock.bin was bugged and rehius removed it.
atmosphere works fine but do i have to restore the boot partition or am i just fine?
I used combined firmware from github but it didn't work so i had to run picofly_tb.bin from hekate (since i already removed the port).
I saw that unlock.bin was bugged and rehius removed it.
atmosphere works fine but do i have to restore the boot partition or am i just fine?
since switch lite has a mariko board yes u can do that way or u just solder it like this without the wires.
if u do it the way its in the picture below and u desolder the cap u MUST Isolate the bottom pad with UV Mask
So, which and how many parts to I need for a Switch Lite and Switch OLED?
I do already got four RP2040-Zeros when this type of Mod was announced first but never looked deeper into it until now.
The Guide tells I need "SMD 8050 47 to 50 ohm Resistors". Do I need 47 AND 50 ohm Resisters or would 47 ohm Resistors be enough? How many do I need?
I found these on Reichelt.de, would this be the correct ones?
I also found this IRFHS8342 MOSFET on Reichelt.de, would be this the correct one?
When it comes to " cpu flex cable", which one would you suggest? Could you send me a link to it? (would need one for my Lite switch and one for my OLED Switch)
Thank you very much in advance
I do already got four RP2040-Zeros when this type of Mod was announced first but never looked deeper into it until now.
The Guide tells I need "SMD 8050 47 to 50 ohm Resistors". Do I need 47 AND 50 ohm Resisters or would 47 ohm Resistors be enough? How many do I need?
I found these on Reichelt.de, would this be the correct ones?
I also found this IRFHS8342 MOSFET on Reichelt.de, would be this the correct one?
When it comes to " cpu flex cable", which one would you suggest? Could you send me a link to it? (would need one for my Lite switch and one for my OLED Switch)
Thank you very much in advance
Last edited by xXDungeon_CrawlerXx,
So, which and how many parts to I need for a Switch Lite and Switch OLED?
I do already got four RP2040-Zeros when this type of Mod was announced first but never looked deeper into it until now.
The Guide tells I need "SMD 8050 47 to 50 ohm Resistors". Do I need 47 AND 50 ohm Resisters or would 47 ohm Resistors be enough? How many do I need?
I found these on Reichelt.de, would this be the correct ones?
I also found this IRFHS8342 MOSFET on Reichelt.de, would be this the correct one?
When it comes to " cpu flex cable", which one would you suggest? Could you send me a link to it? (would need one for my Lite switch and one for my OLED Switch)
Thank you very much in advance
47-50 ohm, so you can use like 47 ohm resistors.
Similar threads
- No one is chatting at the moment.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
@
RedColoredStars:
There is an actual trailer with footage too. lol. Going to watch it tonight. Grabbed it from... a place. -
-
@
SylverReZ:
@Psionic Roshambo, JonTron's back yet again until he disappears into the void for another 6 or so months.+1 -
-
-
