Picofly AIO Thread

snake2 · Mar 29, 2023

Updating from 10.x.x to 16.0.1 fixed my BOOT0 after it got corrupted by unlocking

On Hekate selecting reboot to OFW gave a black screen but I was able to use Atmosphere to boot stock then update over internet

Battlegames · Mar 29, 2023

is possible to use v2 cpu cable on lite and oled?

Adran_Marit · Mar 29, 2023

snake2 said:
Updating from 10.x.x to 16.0.1 fixed my BOOT0 after it got corrupted by unlocking

On Hekate selecting reboot to OFW gave a black screen but I was able to use Atmosphere to boot stock then update over internet

yes, because you booted full stock it fixed the boot0. This is mentioned in the FAQ

urherenow · Mar 29, 2023

It's not mentioned in the FAQ, but in the "Hints" link. I had to hunt for that one.

Adran_Marit · Mar 29, 2023

urherenow said:
It's not mentioned in the FAQ, but in the "Hints" link. I had to hunt for that one.

Yeah it is

If rebooting to OFW vol buttons don't work and blue or black screen

boot into full stock and perform full system reset

edit: my bad. I knew I had it in the op, just had the wrong tab.

urherenow · Mar 29, 2023

Adran_Marit said:
Yeah it is

Ummm... yea... in the Hints link, just as I said (and as you quoted). Not under FAQ.

Adran_Marit · Mar 29, 2023

urherenow said:
Ummm... yea... in the Hints link, just as I said (and as you quoted). Not under FAQ.

As I said my bad, I did know the information was in the OP though

urherenow · Mar 29, 2023

Adran_Marit said:
As I said my bad, I did know the information was in the OP though

It's all good. I was just trying to clarify. I'm OCD'ish... or maybe just straight up OCD...

Dandan0404 · Mar 29, 2023

Should I put Normally Open reed switch in PINS 1 AND 2? so that when magnet comes, it triggers reset?

rskL · Mar 29, 2023

Edit. This post was messed up

jkyoho · Mar 29, 2023

rskL said:
Does anyone know of I get this stuff I'll be set to do this? Anything else I might need

Already have the resistors, flex cable and the rp2040

YOU should be good if you not plan to remove the RP2040 USB-C port otherwise another larger soldering tip for removing the port helps.(unless you have hot air station)

wscp · Mar 29, 2023

Wherre is the 3v3 point for lite?

808080 · Mar 29, 2023

wscp said:
Wherre is the 3v3 point for lite?

look

Kyle46791 · Mar 29, 2023

Does the Toshiba firmware come unlocked already or will I need throw the unlock.uf2 on that too?

Donnie-Burger · Mar 29, 2023

Kyle46791 said:
Does the Toshiba firmware come unlocked already or will I need throw the unlock.uf2 on that too?

Flash toshiba uf2 then flash unlock uf2

So far confirmed working on my end

V1 patched Erista
V2 Mariko

Both with hwfly flex cables
47 - Ohm resistors

papafria · Mar 30, 2023

Hello Dudes!! I really don't know what to do anymore. The picofly sometimes boots and sometimes and sometimes not. I have never get the green blink.. Similarly, despite being able to get hetake to run, I am unable to run atmosphere. Does anyone have any clue as to what's going on? The device is in the latest version, 16.0.1.

JackFrostSMT · Mar 30, 2023

papafria said:
Hello Dudes!! I really don't know what to do anymore. The picofly sometimes boots and sometimes and sometimes not. I have never get the green blink.. Similarly, despite being able to get hetake to run, I am unable to run atmosphere. Does anyone have any clue as to what's going on? The device is in the latest version, 16.0.1.

Looks like your rgb colors are flipped. Try toggling the jumper on the back

papafria · Mar 30, 2023

JackFrostSMT said:
Looks like your rgb colors are flipped. Try toggling the jumper on the back

what do you mean with toggling the jumper dude? and what jumpers exactly?

JackFrostSMT · Mar 30, 2023

papafria said:
what do you mean with toggling the jumper dude? and what jumpers exactly?

Look at the installation diagrams for the rp2040, GRB/RGB jumper
If you have it bridged already like I did, unbridge it
If you don't have it bridged, then bridge it

papafria · Mar 30, 2023

JackFrostSMT said:
Look at the installation diagrams for the rp2040, GRB/RGB jumper
If you have it bridged already like I did, unbridge it
If you don't have it bridged, then bridge it

Thanks Dude... You are the best.. Thats resolve my 1st issue... But now, i dont know why sometimes Success and Sometimes i get the code of Bad CPU pin..

I dont know what to do because of 10 attempms, 5 success and 5 bad cpu pin (without moving anyting)...

I am ussing 2 mosffet IRFHS8342 (1 per each Cap)... Should i use only one?

This is a LCD V2....

¿Any Ideas?

Picofly AIO Thread

Well-Known Member

Member

Walküre's Hacker

Well-Known Member

Walküre's Hacker

Well-Known Member

Walküre's Hacker

Well-Known Member

Well-Known Member

Member

Well-Known Member

Member

Member

Member

Well-Known Member

Member

Attachments

Well-Known Member

Member

Well-Known Member

Member

Attachments

Similar threads

Popular threads in this forum