Can you draw which one?
And can i do it without an soldering iron?
Because i did it at my work
And can i do it without an soldering iron?
Because i did it at my work
When he successfully installed 200+ Hwfly then he will be able to install the pico. I personally don't think installing the pico is risky for an experiences person. I had no problem with the install and I never installed a modchip in my life. But I have around three years in microsoldering experience and a few more years in total. I think you can risk it.
Yea I was informed. Good to know. Next time I will bridge them. That will definiteley improve the reliability of the connection.
- Joined
- Jan 22, 2014
- Messages
- 248
- Trophies
- 1
- Age
- 40
- Location
- Cape Town, Western Cape
- XP
- 1,810
- Country
Use a set of tweezers bridge the 2 points near rat. Then power on. Chip will glow blue then boot into ofw power off then power on then the chip will re train and glitch again
Sent from my iPhone using Tapatalk
Then this is not for you. This picofly is still work in progress and there are many who have bricked the switch. Me myself bricked my patched v1 switch experimenting on this.luckily i have unbricked it. Picofly doesnot fit inside properly without removing the usb port and the two buttons. When you remove them, you will miss a lot if any update comes in future. You will still need to contact to your installer time and again which is a lot of work for him.
As an installer myself, i choose stability for a customer who doubts a lot and brags about how costly and wants 100 percent gurantee.
This picofly is not a stable solution for you. Instead go for hwfly. That way, your installer is also confident, and peace of mind for both you and the installer.
Sent from my SM-G781B using Tapatalk
To everyone who bricked the console attempting this picofly,
Use Sthetix unbricking method.
Start from level 1.
But usually soft bricked will be solved using level 2 method.
You will need a Hwfly modchip though.
Link here.
Sent from my SM-G781B using Tapatalk
Use Sthetix unbricking method.
Start from level 1.
But usually soft bricked will be solved using level 2 method.
You will need a Hwfly modchip though.
Link here.
Sent from my SM-G781B using Tapatalk
Last edited by everyonesweird,
it is enough to flash a clean BOOT0 for your firmware version to fix boot.
https://gbatemp.net/threads/how-to-build-clean-boot0-1-files.591409/
Get some Kapton tape and a bit of solder wick just in case. I would also recommend item 4000241968514. Just search for that number on the site and you will find it.I've already got the flex cable, resistors and rp2040,
Should I get this stuff to help with the install?
If anyone could recommend any changes or other bits that may help, that would be great
View attachment 361986
I had the rgb jumper set like the tutorial, saw no led after write... I'll try unsetting it
It's the recommended IRFHS8342. I had also tried an AO3400, but that didn't work at all.
I got red on program and cyan now.......But gg cap
Im guessing this is needed and can't be left like this?
Similar threads
-
@
RedColoredStars:
i dont know why tv manufactures put the hdmi ports in dumb locations so the cables have to stick out, and then down, putting strain on the ports. Instead of having the ports along the bottom edge of the tv facing downwards. -
-
@
SylverReZ:
@RedColoredStars, I hate that too where you have to use an HDMI extension for an Amazon Fire Stick.+1 -
-
-
-
-
-
@
SylverReZ:
Had a ton of bugs and often crashed. It even didn't support DOS compatibility with older games. :feelsbadman:
-
-
@
RedColoredStars:
I downloaded XP on dialup when it came out. Overnights for like a week. cuz I couldn't tie up the phone line during the day. It was so awesome and worked so great going from ME to XP.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
