On patched systems? That's never gonna happen. Modchips makes injecting a payload possible by fluctuating the voltages on the tegra processor so it skips a check. How would you do that without soldering wires directly to the board?the gateway girl?
Post automatically merged:
I wish one day for a chip that doesn't need soldering
Hi I just install an instinct-nx turn on light was flashing some color begining just remember the last was white then it boot to OFW on a oled model
all the mesurement are
diode mode on multimeter to ground
Black lead to ground and red to each points
A/CMD 0.718 v
B/RST OL
C/DAT0 0.770
D/ CLK 0.766 v
3.3V 0.476 v
SP 1 0.029 v 17.7 ohms
SP 2 0.029 v 17.7 ohms
take a look around seem those measurement very good please give me some advice cose i run out of idea
Thanks
all the mesurement are
diode mode on multimeter to ground
Black lead to ground and red to each points
A/CMD 0.718 v
B/RST OL
C/DAT0 0.770
D/ CLK 0.766 v
3.3V 0.476 v
SP 1 0.029 v 17.7 ohms
SP 2 0.029 v 17.7 ohms
take a look around seem those measurement very good please give me some advice cose i run out of idea
Thanks
![IMG_0142[1].JPG](/data/attachments/364/364097-909f39729fd4f4db4df3cd53696dcbdc.jpg)
ok how do i reflash it? and can u have a look at my testing with multimeter is it correct
diode mode on multimeter to ground
Black lead to ground and red to each points
A/CMD 0.718 v
B/RST OL
C/DAT0 0.770
D/ CLK 0.766 v
3.3V 0.476 v
SP 1 0.029 v 17.7 ohms
SP 2 0.029 v 17.7 ohms
thanks
put this small flex in the connector on the chip board,connect to pc,open the flash.bat
![IMG_0144[1].JPG](https://gbatemp.net/attachments/img_0144-1-jpg.364715/ "IMG_0144[1].JPG")
for readings,my switch is back fully closed now,but try first to reflash
why i say reflash,cause i saw today some video about hwfly,same problem,he flashed the chip,and that solved it.
You can try it,do you have the software?
Post automatically merged:
for readings,my switch is back fully closed now,but try first to reflash
Post automatically merged:
why i say reflash,cause i saw today some video about hwfly,same problem,he flashed the chip,and that solved it.
You can try it,do you have the software?
Last edited by fille,
thanks for your help Fille and Doom
Doom Was Right about the D Point jump a wire end up short it to ground by the D point from the rebon but sorted all good and to Fille as well get the card flashed and everything work boot up to instinct
thanks again
Doom Was Right about the D Point jump a wire end up short it to ground by the D point from the rebon but sorted all good and to Fille as well get the card flashed and everything work boot up to instinct
thanks again
Got one installed in my OLED, works beautifully.
I read in several places that after powering off from OFW with a modchip the system turns back on after ~15 seconds, this one I observed that the chip briefly flashes but system stays off. This is without an SD card inserted so no auto hos off from hekate.
Feature must be baked in the chip firmware ?
I read in several places that after powering off from OFW with a modchip the system turns back on after ~15 seconds, this one I observed that the chip briefly flashes but system stays off. This is without an SD card inserted so no auto hos off from hekate.
Feature must be baked in the chip firmware ?
But they are not redI absolutely recognise those there fingernails in the video
use jump wire straight to the chip, the D point so small and i have ts100 with very fine tip but it not a right tool for this job and make sure u cut the D point off the ribon other wise if it some how pop up and touch the cpu frame will short the switch out
Similar threads
-
-
-
-
-
-
-
-
-
@
Psionic Roshambo:
But other than PC and Amiga ports I don't think Time Soldiers had any game system ports after the Master System -
-
-
@
Psionic Roshambo:
Ohhh just noticed that myself I bet it makes the Master System port look amazing by comparison lol
-
-
-
-
-
-
-
-
-
-
-
@
SylverReZ:
If you want a good system to port it to, at least have a good programmer and knowledge.+1 -
-