Picofly AIO Thread

impeeza · Mar 24, 2023

Adran_Marit said:
This is a Pikofly AIO Thread/Tutorial.
This information has been pulled from other threads and forums on this site, I haven't done anything except compile it in this one thread.
All credit goes to those who worked on all the relevant information and stuff.

First things First; I not not endorse piracy and those who released the firmware don't either so this is for home-brew use only.

DOING THIS MODIFCATION TO YOUR SWITCH MAY CAUSE PERMANENT DAMGE. I RECOMMEND YOU HAVE THIS DONE BY A PROFESSIONAL INSTALLER

DISCLAIMER! Me nor any of the other temp members who helped make this happen will be held liable to any damage you cause your console in attempting to mod it. Professional installation is recommended for this mod.

Just because a mod is cheap doesn't mean it's easy. - Trust me I learnt the hard way - Adran 2023

General Information Installation overview Images Credits

Requirements Hints LED Indicators FAQ's

RP2040-Zero

SMD 8050 47 to 50 ohm Resistors

Mosfet (IRFHS8342 MOSFET) or cpu flex cable (lite flex for lites, v2 flex for v2 mariko etc etc)

switch (duh)

Wire

RP2040 Firmware (direct Link)

Mosfet Images Solder Points

P.S More formatting and information to come

I really love to see the McFly becoming a real thing

Dr_Dankenstein · Mar 24, 2023

wait so I have a v2 switch, I bought some wire and a pico board, also grabbed a v2 flex cable
by the diagrams i would assume my points for a v2 console are just on the emmc? if thats the case do i need this ribon cable when it comes? or do i just follow the diagram here after flashing and solder to the emmc and im good to go?

videos I found seem to show insalls on switch lites mostly?

Dee87 · Mar 24, 2023

Dr_Dankenstein said:
wait so I have a v2 switch, I bought some wire and a pico board, also grabbed a v2 flex cable
by the diagrams i would assume my points for a v2 console are just on the emmc? if thats the case do i need this ribon cable when it comes? or do i just follow the diagram here after flashing and solder to the emmc and im good to go?

videos I found seem to show insalls on switch lites mostly?

v2 flex cable comes on the apu , then u need to solder it to emmc +3v and gnd flash the chip solder everthing to the chip then ur ready to go

Dr_Dankenstein · Mar 24, 2023

ah gotcha thanks
I think i did manage to find an install image too if it helps anyone

kylum · Mar 24, 2023

Dee87 said:
could u link me some good ones for my Oled ?

not really that familiar with reballing the emmc

Best bet is from Ali mate. But if you can wait im sure they will start to show up in other places as well.

Dee87 · Mar 24, 2023

Dr_Dankenstein said:
ah gotcha thanks
I think i did manage to find an install image too if it helps anyone

u can also solder the emmc wires to the board like i did but only do that if ur comfortable with soldering at the emmcu connector :-P

i also solderder a flex connector to the usb port from the rp2040
Klick me 2

Battlegames · Mar 25, 2023

Hello, im trying with a V2 switch but in atmosphere console doesnt wake up after press power button or go to sleep mode, what can i do?

thanks

Donnie-Burger · Mar 25, 2023

Battlegames said:
Hello, im trying with a V2 switch but in atmosphere console doesnt wake up after press power button or go to sleep mode, what can i do?

thanks

Do me a favor and power off and back on then try again. This happened to me once I believe, It's early and there's bugs.

Battlegames · Mar 25, 2023

Donnie-Burger said:
Do me a favor and power off and back on then try again. This happened to me once I believe, It's early and there's bugs.

always happen, other thing is i cant go stock from hekate (black screen)

Post automatically merged: Mar 25, 2023

Battlegames said:
always happen, other thing is i cant go stock from hekate (black screen)

i dont remove 3.3v regulator, could be that?

Donnie-Burger · Mar 25, 2023

Battlegames said:
always happen, other thing is i cant go stock from hekate (black screen)

Post automatically merged: Mar 25, 2023

i dont remove 3.3v regulator, could be that?

If you updated OFW after pico this happens with OFW boot
If you replaced hwfly with pico this happens with OFW

Did you do any of these>? I'm not sure about sleep and 3v3 as I'm waiting for 2.6fw or further news before I remove usbc, port and 3v3 regulator.

Battlegames · Mar 25, 2023

Donnie-Burger said:
If you updated OFW after pico this happens with OFW boot
If you replaced hwfly with pico this happens with OFW

Did you do any of these>? I'm not sure about sleep and 3v3 as I'm waiting for 2.6fw or further news before I remove usbc, port and 3v3 regulator.

i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

meha · Mar 25, 2023

Hello guys, I'm planning to install on mariko. Do I need to remove the buttons/port or does it fit inside switch? Thanks

Donnie-Burger · Mar 25, 2023

Battlegames said:
i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

Did you use 47 Ohm resistors?

Battlegames · Mar 25, 2023

Donnie-Burger said:
Did you use 47 Ohm resistors?

yes , on cmd, clk and dat0

Adran_Marit · Mar 25, 2023

Battlegames said:
i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

yes always use the original downloads.

if you updated your firmware recently you need to boot full stock.

Dee87 · Mar 25, 2023

Battlegames said:
i dont do any of these, im using hats from sthetix , maybe could try original atmosphere?

Its not hats I have hats also running

Adran_Marit · Mar 25, 2023

Dee87 said:
Its not hats I have hats also running

Just cause it works foe you doesn't mean it won't work for someone else

minik1971 · Mar 25, 2023

BUENOS DIAS COMPAÑEROS ME PODRIAN DAR LOS DIAGRAMAS PARA LA PICOFLY PARA V1 GRACIAS

brecht6 · Mar 25, 2023

Adran_Marit said:
.
.
.

Changelog: Added Erista v1? diagram

P.S More formatting and information to come

It's a v2

Adran_Marit · Mar 25, 2023

brecht6 said:
It's a v2

V1 and v2. Got clarification from my source. Oled diagrams are coming at some point sooon

Picofly AIO Thread

¡Kabito!

Member

Well-Known Member

Member

Attachments

Well-Known Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Member

Walküre's Hacker

Well-Known Member

Walküre's Hacker

Active Member

Active Member

Walküre's Hacker

Similar threads

Popular threads in this forum