Recent content by Peeta01

  1. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    On the multimeter what settings did you set to read point b? I dont think its diode mode. I borrow an untouched oled switch and read it on diode mode there no reading.
  2. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Any links to the flash files?
  3. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Thanks! Hm i think i forgot to wire the ground on the chip to the board? But the v5 hwfly doesnt seem like it needs to, due to the ribbon. Probably pulling gnd from the top of 3v3. But would that change b point value when connected?
  4. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Can you link me the video? What does it mean when point b doesn't have any value? Thanks!
  5. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    There's continuity from the board to the chip. So the wires are good. Just no reading. Can i use another point? Or check somewhere to see why point b isn't giving out anything? Thanks!
  6. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Yes it went throught the inital training flashing yellow then purple then green/yellos purple and end with red. So... am i suppose to get anything reading from point B? 1670085162 Yeah it stays on OL when testing Point B.
  7. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Hmm i didnt get any reading on point B (diode mode). Not sure why. Even try reading directly from point B but i didnt see a reading. I read somewhere it say check for continuity only. But maybe thats where my error is. Ill try to desolder point b to see if i can get a reading. Thanks! 1670080068...
  8. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Tested diode mode on chip points d = .73v A = .726v C = .73v 3v3= .74v gnd = 0 beep B check continuity it beeps. Flashing purple, flash green, flash purple and end with red light and boots onto original system. Can't figure where the issue is. sp1 and sp2 diode mode reads 0.013v with beeps. TIA.
  9. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Since you mention that. What temperature are you guys using? I think one time i used too high and it burn out the padding on the ribbon. I dont know if it was that or cheap manufacturing.
  10. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Thanks! Hm... heres the IS tips.
  11. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Thank you!
  12. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Like these?
  13. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    One last thing, what type of soldering tip are you guys using? I seen some people use the IS. Is that better with trying get solder on point D?
  14. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

  15. P

    HWFLY OLED install. I can't get the DAT0 connector to connect.

    Thank you, sir!
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    SylverReZ @ SylverReZ: @Psionic Roshambo, Thats pretty cool.