Recent content by LazarusGX4

  1. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ....hi again, eMMCs have arrrived and tried to restore the backup... ...no user partitions on the eMMCs...also slow speed... (before restore) ...then after restoring eMMC backup, still Black Screen on OFW... :( ...or it will not work because the new eMMC has a different serial ID...
  2. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ..I have done eMMC backup after installing PicoFly... ..I soldered the 3.3v to this point on the eMMC Board...
  3. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    no, only Hecate... Atmosphere hangs on splash screen when I try to load Fusee Payload...
  4. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...nope, blackscreen also... :(
  5. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...even EmuMMC blackscreens... :( ..I already done: - recovering sysMMC from backup - trying donor eMMC - re installing BOOT 0 & 1 - creating EmuMMC... ..probably it son the Hardware side now.. :( ..already ordred eMMC Module on Ali... see if it works..
  6. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...on pico, I was initially using the 2.74 FW and tried to downgrade it to 2.73 thinking it might have an effect on it...same result :(
  7. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...hi again, I tried to add resistance to CMD as suggested.... ..but still..
  8. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks for the tip :) will also try that once I get over this ordeal :cry:
  9. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks :) i will try that :)
  10. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    hi, thanks for the replies :) it was booting ok (OFW) before installing the Pico...I used the 3v from the eMMC Module... ...the eMMC can still be accessed by Hekate and not in Slow Mode... ...I might have to try going 100 ohms on the CMD as @abal1000x suggested.. though I'll have to find...
  11. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...hi, i just tried to install picofly on a V1 Patched Erista and I was able to boot to Hekate, but when rebooting to OFW I get Black screen, I tried to remove the Pico and still black screen... ..Thinking I might have corrupted BOOT 0 so I tried to restore from Backup but still same...
  12. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...nice! :)
  13. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ..I experienced that (Switch Lite though..)...then after the glitching attempt a RED LED then off... what I did is to replace my wirings with enameled 0.2mm (DAT0, CMD, RST, CLCK, CPU) then it worked... It might also be a soldering issue (cold solder?)...
  14. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...Alternate Solder Points for DAT0, CMD, CLK, RST ...(??????????) on Switch Lite ???? For Confirmation.... from http://balika011.hu/switch/lite/
  15. L

    Hacking Hardware Picofly - a HWFLY switch modchip

    ...It works now :) ...it seems that for the RST/CPU/CLK/DAT0/CMD -- I should have used same type of wire (enameled 0.2)... i was using a mix of kynar (awg 30) and enameled wire, and I was getting Blue > Red LED (maybe Timed Out? / Timing Issue?) when I replaced the wires and made them the...
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    Psionic Roshambo @ Psionic Roshambo: https://www.youtube.com/@legolambs