I see nothing,maybe tomorrow at work with magnifying glass...?
But if the sd is the problem, why can i enter hekate,and why can i load the payload?
View attachment 167257 View attachment 167258
5) Grounded:
May i every time reinstall all screws,backplate,everithing,or can i try without the alu+plastic backplate?
Used this for reference btw.
Yeah probably the angle of light, best for him to quickly check this though, SMD components of that size drive me mad, they're very delicate; though easily replaced.Yeah forget the shield. The main aliminium cast chassis GNDs everything
Possible. But may be a slightly different board revision or filter cap for regional purposes, or angle of the light catching it...
Yep. The caps are tougher than resistors. Absolutely correct. Easily replaced.Yeah probably the angle of light, best for him to quickly check this though, SMD components of that size drive me mad, they're very delicate; though easily replaced.
I'm not good with figuring the value since my multimeter is trash but mattyrog may be able to check it and repair it for you; I'd be happy to repair it if that's the case and the value can be given, I'll do it for postage cost and part cost only since I want to show the community a gesture of goodwill so I can start doing modchip installs from trust of the community.I think you found the problem...
View attachment 167259
@Rain82 PLEASE PLEASE PLEASE don`t attempt to bridge it. It could be a filter cap going between V+ & GND - Result instant death.Yep. That would do it. Well spotted Tariq! Just need the value now measured out of circuit. Will have a look on a scrap board tomorrow. Can`t tonight. Everyone in bed
Keep us informed sir!Thanks, tomorrow at work we check and try to fix it, my colleague is a technician with good skill. Ill report back after.
Thank you all!
--------------------- MERGED ---------------------------
I dont try, i am not good at this kind of electronics. Im consulting w my colleague tomorrow. And thanks.
I hope we can fix it.
Ill report back as soon as i know something.
And please if you have any measurement tomorrow from a scrap board please let me know.
Good night!
--------------------- MERGED ---------------------------
Measurement of smd resistance. Something that helps
You can also summon Joseph Fourier to aid with a frequency response analysis to infer the capacitance.Can`t measure resistance on a capacitor, esp in a DC circuit! Meaningless almost! Measure reactance in an AC circuit, sure... But its all DC here sir!
We need old Mick Faraday... Georg Ohm just can`t handle it right now!
Send it over here. PM me for possible repair sir. Only got 4 coming this and next week... Rather quiet next week!Eh,its a little chinese for me...:/ Can we do something, or am i destroyed the switch?
Nice idea! But the man seems obsessed with Greenhouses and Gases... Is he growing Tomatoes? Using Fart to power a heater for them?You can also summon Joseph Fourier to aid with a frequency response analysis to infer the capacitance.
I'm not good with figuring the value since my multimeter is trash but mattyrog may be able to check it and repair it for you; I'd be happy to repair it if that's the case and the value can be given, I'll do it for postage cost and part cost only since I want to show the community a gesture of goodwill so I can start doing modchip installs from trust of the community.
Yep. That would do it. Well spotted Tariq! Just need the value now measured out of circuit. Will have a look on a scrap board tomorrow. Can`t tonight. Everyone in bed
--------------------- MERGED ---------------------------
@Rain82 PLEASE PLEASE PLEASE don`t attempt to bridge it. It could be a filter cap going between V+ & GND - Result instant death.
But more than likely, it is being used for decoupling or timing.
Please help.
My Switch stucked at Nintendo Switch logo screen after thermal paste change...I can load reinx with tegrarcm so the sdcard working, but after reinx logo, its stucked at Switch logo...
Any tips,help? Thanks..