Search results

  1. Devon093

    Hardware Switch gets stuck at Switch Logo upon boot. (Not M92)

    Thanks for the replies, due to my motherboard model, this unit is patched and cannot be hacked correct? Which also means i could not create a nand backup either?
  2. Devon093

    Hardware Switch gets stuck at Switch Logo upon boot. (Not M92)

    Hello all, I have a switch here that powers on, and gets stuck at the Switch Logo upon boot. I have fixed nearly identical issues in the past by replacing the M92T36. I swapped the IC on this unit and there was not change in the issue. Before the swap, i tested voltage to pins 5 and 6 and had...
  3. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    I replaced the alleged DC/DC converter and had no change unforunately. At least its not worse than it was. I cannot be 100% sure my swap was flawless though. Back to square one for now :(
  4. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    Oh boy watch your step, however could you take a look at the other post i tagged you in? I found a chipped component and am likely going to replace it tomorrow. If you have any advice on that it is appreciated :)
  5. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    It honestly did slip my mind that the sync button existed which will be helpful to remember in the future
  6. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    The issue with the joycon has been fixed which you can take a look at the previous posts It was fixed by repalcing a mosfet. Thanks for the advice though!
  7. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    @SolidSnakeUk89 So I have a working LCD, checked the diodes and they seem good, as well as the inductor passthrough components and those seem alright. I suddenly noticed something i didnt see before, what appears to be a damaged IC near the LCD clip. It looked like a piece of glass was wedged...
  8. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    THanks for continuing to reply, I have fixed som bent pin LCD ribbon clips before, and also replaced one entirely. I checked for bent pins I have checked the test points near the LCD, one of them is ground. Out of the other 4 2 pins have 1.8V, which i also tested on another board and that...
  9. Devon093

    Hardware Strange Switch Error - Gets Stuck with black screen after locking it

    I have actually 2 separate Stock Firmware Nintendo Switch consoles with the same issue. This issue is not 100% consistent, sometimes it happens sometimes it does not. When the consoles work, I can power them on, and play them for hours but as soon as i press the lock button, I am unable to...
  10. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    So... This is awkward. I had a friend help me with the reassembly and ive encountered a new problem. The unit appears to be not displaying video in handheld mode. The back light is coming on, the unit is booting since i can use the touch screen, and also outputs correctly through docking...
  11. Devon093

    Hardware Repair Log thread for motherboard and Joycon PCB repair logs

    Swapped M92 and was successful, pins must have crossed in the broken USB-C and damaged the IC as well. Thanks for the help, now i have a new way to test M92 minus just looking for shorts :)
  12. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    It was honestly a long shot, since the switch was charging the joycons i wanted to try and avoid things i knew were power related. I noticed that the PU chip i replaced and the other one in the picture which is marked MX are on both ends of the board each on the opposite side of the joycon...
  13. Devon093

    Hardware Repair Log thread for motherboard and Joycon PCB repair logs

    I will try to swap it monday, i do have some spares. Thanks so much and ill be sure to let you know my results
  14. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    Fixed! Swapped one of the 6 pin chips marked "PU" Picture provided!
  15. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    I reallllly hope it is not the MAX77621AEWI, I don't think im capable of swapping it. Perhaps ill try one of those mosfets and just hope for the best, and if not maybe those smalled BGA chips Agilato mentioned
  16. Devon093

    Hardware Repair Log thread for motherboard and Joycon PCB repair logs

    Thank you for this reply, i have a USB c multimeter and i was getting no reading with the switch, unfortunately it wasnt turning on with the NSW ac adapter so i used my pc usb. Took out the board, no corrosion. Assuming i checked the right pins on the m92, i have .291v on pin5, and virtually...
  17. Devon093

    Hardware Repair Log thread for motherboard and Joycon PCB repair logs

    I like this thread so i will ask for help here regarding a non charging switch. Switch powers on and had physically damaged USB-C port. I replaced it (as I have maybe 15 times before) and i am not getting a charge in either direction of the usb c cable. The fuse near the port is good, and im...
  18. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    I am going to look into the ICs you are reffering to, and maybe try a swap. If im unsuccessful i assume the functionality will not change hopefully. And yeah i figured that too since it never know the joycon is connected to the console so youd be stuck at initial set up.. Ill take a look soon...
  19. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    Any ideas from anyone? I tried looking for shorts in the connector for the joycon but they all seem normal. Anyone know what IC controls them? *fancy bump
  20. Devon093

    Hardware Switch will not recognize that Joycon is attached, and cannot sync new joycons

    Sorry if I confused ya, I'm aware of what you meant. Which means that the issue is likely a component on the board i just need to locate it.
General chit-chat
Help Users
  • No one is chatting at the moment.
    LeoTCK @ LeoTCK: yes for nearly a month i was officially a wanted fugitive, until yesterday when it ended