Search results

  1. ryuga93

    Square Enix Threatens Legal Action Against Type-0 Fan Translation

    After reading the kotaku article, it seems that Sky has some fault in it but still if SE sues him under copyright reason I think it is unfair,unless they also sued the chinese translation team too, because there are lots of pre-patched iso around the chinese websites,be it either a two disc iso...
  2. ryuga93

    Square Enix Threatens Legal Action Against Type-0 Fan Translation

    I'm used to be square enix fans because of Kingdom Hearts, but this has changed my view to Square Enix, scew you Square, why don't you shot down the Chinese translation of the game which came out after a few months after the release too?:dry: What they just care is their money lol
  3. ryuga93

    Misc Nintendo Zone Charizard Distribution

    How did you change the MAC of the hostednetwork to those values?
  4. ryuga93

    Hacking My Gateway hunch won't fail me

    This わしは神だ　:bow:
  5. ryuga93

    Hacking 3DS/DS Flashcart all in one?

    I wonder how many man power they have?:blink:
  6. ryuga93

    Kingdom Hearts HD 2.5 ReMIX release date confirmed (PS3)

    There is a room for the story of those who are wondering in Realm of Darkness, just like in the BBS FM secret ending, but this would be more to a filler Loved all version of Dearly Beloved, and Vector To Heavens
  7. ryuga93

    Kingdom Hearts HD 2.5 ReMIX release date confirmed (PS3)

    Where is KH BBS 2?:(
  8. ryuga93

    Hacking 3DS unbricking progress

    So how is the log after input X?
  9. ryuga93

    Hacking 3DS unbricking progress

    May I know what device you are using to interface the 3ds and arduino? An IC or SD card shield? And what arduino you are using? The init is fine but the read CID operation is not functioning. Try input x (terminate execution) and get the output log. (It will show the MMC info)
  10. ryuga93

    Hacking 3DS unbricking progress

    Could you post the log for the initialisation? The one before asking which function you want.
  11. ryuga93

    Hacking 3DS unbricking progress

    May I know which arduino you are using? How about try to remove the card after locking then reinsert and do the unlock again.
  12. ryuga93

    Hacking Unbricking regular 3DS

    If you are going to solder the the 3ds then it is better to use the clock solder point under the mobo, but you will need to take the whole board out, and remember to use soldering flux. I don't recomend to solder the clock point as it is very small, unless you want to keep the mod. What I did is...
  13. ryuga93

    Hacking 3DS unbricking progress

    No, connect the teensy to just a sd card and check whether it runs well by locking the sd card then unlock again. After you have confirm that it works, perform the unlock on 3ds
  14. ryuga93

    Hacking 3DS unbricking progress

    Try the code on a regular sd card first. The code does not seem run quite stable on teensy An easy regular 3ds hardmod would be good, due to the tiny clock pin, plus the whole mobo needs to be taken out
  15. ryuga93

    Hacking 3DS unbricking progress

    A seeedstudio sd card shield that uses IC as voltage converter instead of resistors, a user reported that it worked for him but luck was not on my side....The wire length should be ok
  16. ryuga93

    Hacking 3DS unbricking progress

    The connections are as the schematic on the github. I think the critical part is to find an IC that is compatible to the 3ds, and try to keep the wires as short as possible. If possible can you try it with sn74lvc245? A user is able to initialise the 3ds using this IC, but haven't perform any...
  17. ryuga93

    Hacking EMUNAND 4.5 On Higher Firmware Version

    Yea, the video does not show any information...the only clue in the video is the Miiverse icon. Because the original system version is 7.1 and running emunand on it causes the icon to appear on the emunand
  18. ryuga93

    Hacking EMUNAND 4.5 On Higher Firmware Version

    So I came across this thread while going through the Chinese Forum. Source: http://tieba.baidu.com/p/3010230197 Another link with video: http://tieba.baidu.com/p/2969520371 (Note the Miiverse icon on the 3ds)
  19. ryuga93

    Hacking 3DS unbricking progress

    Have you tested all your connections? However, I think the main problem is how you step down the voltage from 5v to 3.3v.
  20. ryuga93

    Hacking 3DS unbricking progress

    For the arduino a logic converter IC (I MEAN AN IC CHIP) is needed, I have tested with 2 sd shield that uses IC to step down the voltage but not working...All the connections are fine cuz the NAND can be detected with RPI.
General chit-chat
Help Users
  • No one is chatting at the moment.
    K3Nv2 @ K3Nv2: https://youtu.be/MddR6PTmGKg?si=mU2EO5hoE7XXSbSr